Page 1 — L381/L382/L383
SIRUBA 銀箭牌工業用縫紉機 INDUSTRIAL SEWING MACHINE L381/L382/L383 使用說明書/零件圖 INSTRUCTION BOOK/PARTS LIST CE KAULIN MFG. CO., LTD. L382 MFG. NO. jintex.in KAULIN MFG. CO., LTD.
Parts index — Siruba L381tap a row to open its page
Page 14
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| ① | ① | screw | |
| ② | ② | set screw |
Page 18 — The position of the thread-amount adjusting plate of the thread take-up lever (Fig.28) / Frame thread eyelet (Fig.29) / Replacement of throat plate (Fig.30)
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 80~50 | Cotton thread | ||
| 80~50 | Cotton thread | ||
| 80~50 | Thread of chemical fibre | ||
| 80~50 | Thread of chemical fibre |
Page 19 — 二十七、缝纫机的保养 / Maintenance of the machine
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | Needle clamp | ||
| 2 | Hinged foot | ||
| 3 | Throat plate | ||
| 4 | Feed dog | ||
| 5 | Rear moving needle guard | ||
| 6 | Curler | ||
| I | 断线 |
Page 22
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 4 | Breakage of needle | ||
| 5 | Puckering |
Page 25
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 9 | 9 | ||
| 7 | 7 | ||
| 8 | 8 | ||
| 10 | 10 | ||
| 4 | 4 | ||
| 5 | 5 | ||
| 6 | 6 | ||
| 40 | 40 | ||
| 41 | 41 | ||
| 42 | 42 | ||
| 1 | 1 | ||
| 43 | 43 | ||
| 11 | 11 | ||
| 13 | 13 | ||
| 12 | 12 | ||
| 14 | 14 | ||
| 15 | 15 | ||
| 40 | 40 | ||
| 45 | 45 | ||
| 44 | 44 | ||
| 38 | 38 | ||
| 39 | 39 | ||
| 16 | 16 | ||
| 3 | 3 | ||
| 17 | 17 | ||
| 36 | 36 | ||
| 37 | 37 | ||
| 2 | 2 | ||
| 19 | 19 | ||
| 26 | 26 | ||
| 27 | 27 | ||
| 20 | 20 | ||
| 48 | 48 | ||
| 32 | 32 | ||
| 34 | 34 | ||
| 33 | 33 | ||
| 35 | 35 | ||
| 31 | 31 | ||
| 30 | 30 | ||
| 29 | 29 | ||
| 28 | 28 | ||
| 21 | 21 | ||
| 22 | 22 | ||
| 23 | 23 | ||
| 24 | 24 | ||
| 25 | 25 | ||
| 46 | 46 | ||
| 47 | 47 |
Page 26 — 1、机壳分组件 Arm bed components
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GQ202/13 | 机壳部件 | ||
| GS0127 | 底板支承螺钉 | ||
| GR1823 | 底板支承板 | ||
| GK186 | 后窗板 | ||
| GR1812 | 后窗垫 | ||
| GS100 | 后窗板螺钉 | ||
| GR1757/2 | 面板部件 | ||
| GR1758 | 面板垫 | ||
| GS100 | 面板螺钉 | ||
| GR1458 | 面板调节螺孔塞 | ||
| GR1813 | 凸轮盖压板 | ||
| GW287 | 凸轮盖压板弹簧 | ||
| GR1814 | 凸轮盖压板弹簧座 | ||
| GS069 | 凸轮盖压板弹簧座螺钉 | ||
| GM241 | 附件安装板 | ||
| GW288 | 附件安装板弹簧 | ||
| GS0128 | 附件安装板弹簧螺钉 | ||
| GS012 | 附件安装板定位螺钉 | ||
| GM242/9 | 凸轮盖部件 | ||
| GM243 | 凸轮盖 | ||
| GW289 | 凸轮盖托板 | ||
| GW290 | 凸轮盖弹簧 | ||
| GS045 | 凸轮盖弹簧螺钉 | ||
| GR1815 | 凸轮盖导轮 | ||
| GS0129 | 凸轮盖导轮螺钉 | ||
| GM244/6 | 推板部件 | ||
| GM245 | 推板 | ||
| GW291 | 推板弹簧 | ||
| GS045 | 推板弹簧螺钉 | ||
| GR1816 | 推板导轮 | ||
| GS0129 | 推板导轮螺钉 | ||
| GW292 | 推板锁簧 | ||
| GS010 | 推板锁簧螺钉 | ||
| GR1817 | 推板翼把手 | ||
| GS44 | 推板翼把手螺钉 | ||
| GR1818 | 送料轴底板挡油板 | ||
| GS010 | 底板挡油板螺钉 | ||
| GR1819 | 底板挡油板油板 | ||
| GS010 | 底板挡油板螺钉 | ||
| GR1461 | 轴套定位螺孔塞 | ||
| GR1462 | 上轴套油线孔塞 | ||
| GR1463 | 针杆柄螺孔塞 | ||
| GR1464 | 送料针距调节器孔塞 | ||
| GR1465 | 抬牙轴孔塞 | ||
| GR1466 | 下轴盲孔塞 | ||
| GR1916/5 | 卷边部件(1/4") | ||
| GR1923 | 卷边垫块 | ||
| GS0148 | 卷边器螺钉 |
Page 27
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | 1 | Screw | |
| 2 | 2 | Pulley | |
| 3 | 3 | Screw | |
| 4 | 4 | Washer | |
| 5 | 5 | Shaft | |
| 6 | 6 | Collar | |
| 7 | 7 | Collar | |
| 8 | 8 | Set Screw | |
| 9 | 9 | Shaft | |
| 10 | 10 | Pin | |
| 11 | 11 | Collar | |
| 12 | 12 | Spring | |
| 13 | 13 | Screw | |
| 14 | 14 | Screw | |
| 15 | 15 | Screw | |
| 16 | 16 | Screw | |
| 17 | 17 | Shaft | |
| 18 | 18 | Screw | |
| 19 | 19 | Washer | |
| 20 | 20 | Screw | |
| 21 | 21 | Screw | |
| 22 | 22 | Shaft | |
| 23 | 23 | Screw | |
| 24 | 24 | Shaft | |
| 25 | 25 | Nut | |
| 26 | 26 | Screw | |
| 27 | 27 | Shaft | |
| 28 | 28 | Pin | |
| 29 | 29 | Cap | |
| 30 | 30 | Shaft | |
| 31 | 31 | Screw | |
| 32 | 32 | Shaft | |
| 33 | 33 | Screw | |
| 34 | 34 | Shaft | |
| 35 | 35 | Shaft | |
| 36 | 36 | Screw | |
| 37 | 37 | Shaft | |
| 38 | 38 | Bracket | |
| 39 | 39 | Screw |
Page 28 — 2、上轴针杆分组件 Main shaft & needle bar components
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GS02 | 上轴安全螺钉 | ||
| GP132 | 上轮 | ||
| GS03 | 上轮螺钉 | ||
| GR1468/2 | 上轴油封 | ||
| GZ303 | 上轴 | ||
| GO262/2 | 上轴后轴套部件 | ||
| GR1824 | 上轴挡圈 | ||
| GS33 | 上轴挡圈螺钉 | ||
| GO265-1 | 上轴中轴套部件 | ||
| GS05 | 中轴套螺钉 | ||
| GO303/2 | 上轴前轴套部件 | ||
| GS04 | 轴套螺钉 | ||
| GR1470 | 曲柄油量限制毡 | ||
| GX334 | 曲柄油量调节销 | ||
| GO269 | 曲柄油量调节销套 | ||
| GR1471 | 曲柄油量调节销O形圈 | ||
| GH378 | 针杆曲柄 | ||
| GS06 | 针杆曲柄定位螺钉 | ||
| GR1472 | 定位螺钉O形圈 | ||
| GS07 | 针杆曲柄紧固螺钉 | ||
| GH379 | 针杆连杆销 | ||
| GS48 | 挑线曲柄定位螺钉 | ||
| GS041 | 挑线曲柄螺钉 | ||
| GH334 | 针杆连杆连杆 | ||
| GO270 | 针杆连杆滚针轴承 | ||
| GS09 | 针杆连杆左旋螺钉 | ||
| GO271 | 针杆上衬套 | ||
| GS012 | 针杆上衬套螺钉 | ||
| GR1479 | 针杆上衬套孔塞 | ||
| GO288 | 针杆下衬套 | ||
| GR1478-7 | 针杆连接柱 | ||
| GS011 | 针杆连接柱螺钉 | ||
| GU168-7 | 针杆连接柱滑块 | ||
| GZ304 | 针杆 | ||
| GR1826 | 针夹(1/4") | ||
| GS0130 | 支针螺钉 | ||
| GV18 | 机针 | ||
| GR0341-7 | 针杆接头滑块导轨 | ||
| GS766 | 滑块导轨螺钉 |
Page 29
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 24 | 24 | Screw | |
| 25 | 25 | Washer | |
| 28 | 28 | Rod | |
| 29 | 29 | Spring | |
| 30 | 30 | Hook | |
| 31 | 31 | Lever | |
| 22 | 22 | Lever | |
| 26 | 26 | Spring | |
| 27 | 27 | Screw | |
| 32 | 32 | Screw | |
| 33 | 33 | Screw | |
| 20 | 20 | Bracket | |
| 23 | 23 | Screw | |
| 21 | 21 | Screw | |
| 16 | 16 | Screw | |
| 15 | 15 | Lever | |
| 19 | 19 | Screw | |
| 17 | 17 | Bracket | |
| 18 | 18 | Lever | |
| 34 | 34 | Rod | |
| 1 | 1 | Nut | |
| 2 | 2 | Screw | |
| 4 | 4 | Spring | |
| 3 | 3 | Washer | |
| 6 | 6 | Screw | |
| 7 | 7 | Screw | |
| 9 | 9 | Cord | |
| 5 | 5 | Screw | |
| 11 | 11 | Screw | |
| 10 | 10 | Bracket | |
| 8 | 8 | Shaft | |
| 36 | 36 | Washer | |
| 14 | 14 | Screw | |
| 13 | 13 | Spring | |
| 12 | 12 | Lever |
Page 30
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | GS018 | 调压螺钉 | 1 |
| 2 | GL18 | 调压螺钉螺母 | 1 |
| 3 | GR1494 | 调压导杆 | 1 |
| 4 | GW253 | 调压簧 | 1 |
| 5 | GZ305 | 压杆 | 1 |
| 6 | GR1827 | 压杆导架 | 1 |
| 7 | GS019 | 压杆导架螺钉 | 1 |
| 8 | GO273 | 压杆衬套 | 1 |
| 9 | GR1525 | 压杆油线 | 1 |
| 10 | GM246/5 | 压脚部件1/4" | 1 |
| 11 | GS020 | 压脚螺钉 | 1 |
| 12 | GR1832 | 切线刀 | 1 |
| 13 | GR1833 | 切线刀导钩 | 1 |
| 14 | GS0129 | 切线刀导钩螺钉 | 1 |
| 15 | GR1499 | 压脚扳手 | 1 |
| 16 | GS021 | 压脚扳手螺钉 | 1 |
| 17 | GR1500 | 压脚扳手垫圈 | 1 |
| 18 | GR1501/2 | 压脚扳手凸轮部件 | 1 |
| 19 | GR1503 | 压脚扳手轴O形圈 | 1 |
| 20 | GR1504 | 压脚升降板 | 1 |
| 21 | GS022 | 升降板轴位螺钉 | 1 |
| 22 | GR1505 | 抬压脚前杠杆 | 1 |
| 23 | GS023 | 前杠杆轴位螺钉 | 1 |
| 24 | GS024 | 前杠杆螺纹销 | 1 |
| 25 | GR1506 | 前杠杆螺纹销垫圈 | 1 |
| 26 | GR1508 | 前杠杆特制开口挡圈 | 1 |
| 27 | GR1507 | 前杠杆开口挡圈 | 1 |
| 28 | GR1834 | 抬压脚拉杆 | 1 |
| 29 | GS025 | 抬压脚拉杆螺钉 | 2 |
| 30 | GR1510 | 抬压脚拉杆开口挡圈 | 2 |
| 31 | GR1835 | 抬压脚后杠杆 | 1 |
| 32 | GS0131 | 后杠杆轴位螺钉 | 1 |
| 33 | GR1836 | 抬压脚顶杆接头 | 1 |
| 34 | GX378 | 抬压脚顶杆 | 1 |
| 35 | GL19 | 抬压脚顶杆螺钉 | 1 |
| 36 | GR1353-7 | 压杆密封套 | 1 |
Page 31
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | 1 | SHAFT | |
| 2 | 2 | SHAFT | |
| 3 | 3 | SHAFT | |
| 4 | 4 | SHAFT | |
| 5 | 5 | SHAFT | |
| 6 | 6 | SHAFT | |
| 7 | 7 | SHAFT | |
| 8 | 8 | SHAFT | |
| 9 | 9 | SHAFT | |
| 10 | 10 | SHAFT | |
| 11 | 11 | SHAFT | |
| 12 | 12 | SHAFT | |
| 13 | 13 | SHAFT | |
| 14 | 14 | SHAFT | |
| 15 | 15 | SHAFT | |
| 16 | 16 | SHAFT | |
| 17 | 17 | SHAFT | |
| 18 | 18 | SHAFT | |
| 19 | 19 | SHAFT | |
| 20 | 20 | SHAFT | |
| 21 | 21 | SHAFT | |
| 22 | 22 | SHAFT | |
| 23 | 23 | SHAFT | |
| 24 | 24 | SHAFT | |
| 25 | 25 | SHAFT | |
| 26 | 26 | SHAFT | |
| 27 | 27 | SHAFT | |
| 28 | 28 | SHAFT | |
| 29 | 29 | SHAFT | |
| 30 | 30 | SHAFT | |
| 31 | 31 | SHAFT | |
| 32 | 32 | SHAFT | |
| 33 | 33 | SHAFT | |
| 34 | 34 | SHAFT | |
| 35 | 35 | SHAFT | |
| 36 | 36 | SHAFT | |
| 37 | 37 | SHAFT | |
| 38 | 38 | SHAFT | |
| 39 | 39 | SHAFT | |
| 40 | 40 | SHAFT | |
| 41 | 41 | SHAFT | |
| 42 | 42 | SHAFT | |
| 43 | 43 | SHAFT | |
| 44 | 44 | SHAFT | |
| 45 | 45 | SHAFT | |
| 46 | 46 | SHAFT | |
| 47 | 47 | SHAFT | |
| 48 | 48 | SHAFT | |
| 49 | 49 | SHAFT | |
| 50 | 50 | SHAFT | |
| 51 | 51 | SHAFT | |
| 52 | 52 | SHAFT | |
| 53 | 53 | SHAFT | |
| 54 | 54 | SHAFT | |
| 55 | 55 | SHAFT | |
| 56 | 56 | SHAFT | |
| 57 | 57 | SHAFT | |
| 58 | 58 | SHAFT | |
| 59 | 59 | SHAFT | |
| 60 | 60 | SHAFT | |
| 61 | 61 | SHAFT | |
| 62 | 62 | SHAFT | |
| 63 | 63 | SHAFT | |
| 64 | 64 | SHAFT | |
| 65 | 65 | SHAFT | |
| 66 | 66 | SHAFT | |
| 67 | 67 | SHAFT |
Page 32 — 4、送料分组件 Feed mechanism components
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GT160/10 | 送料偏心轮部件 | ||
| GT161 | 送料偏心轮 | ||
| GS034 | 送料偏心轮螺钉 | ||
| GR1521 | 送料偏心轮盖板 | ||
| GS035 | 送料偏心轮盖板螺钉 | ||
| GH335 | 送料大连杆 | ||
| GH380 | 送料小连杆 | ||
| GX340 | 送料连杆销 | ||
| GS036 | 送料连杆销螺钉 | ||
| GR1522 | 送料摆杆 | ||
| GR1523 | 送料摆杆座 | ||
| GX341 | 送料摆杆座左销 | ||
| GS037 | 送料摆杆座左销螺钉 | ||
| GX342 | 送料摆杆座右销 | ||
| GS05 | 送料摆杆座右销螺钉 | ||
| GZ279 | 送料摆杆销 | ||
| GS038 | 送料摆杆销螺钉 | ||
| GS039 | 送料曲柄轴位螺钉 | ||
| GL7 | 送料曲柄轴位螺母 | ||
| GH337 | 送料曲柄 | ||
| GS040 | 送料曲柄螺钉 | ||
| GZ280 | 送料轴 | ||
| GR1890 | 送料轴薄挡圈 | ||
| GS032 | 送料轴薄挡圈螺钉 | ||
| GR1524 | 送料轴挡圈 | ||
| GO285 | 送料轴后挡套 | ||
| GS41 | 送料轴后挡套螺钉 | ||
| GR1469 | 送料轴挡圈 | ||
| GS39 | 送料轴挡圈螺钉 | ||
| GZ286 | 送料轴前挡套 | ||
| GR1838 | 牙架 | ||
| GS0120 | 牙架螺钉 | ||
| GR1528 | 牙架座螺钉垫圈 | ||
| GL20 | 牙架座螺钉垫母 | ||
| GR1839 | 牙架 | ||
| GX396 | 牙架销 | ||
| GS0100 | 牙架销螺钉 | ||
| GR1837 | 牙架销油线 | ||
| GM247 | 送料牙1/4" | ||
| GR1528 | 送料牙垫圈 | ||
| GS019 | 送料牙螺钉 | ||
| SM248 | 送料板1/4" | ||
| GS044 | 送料板螺钉 | ||
| GH381 | 送料牙连杆 | ||
| GR1840 | 拆牙连杆凸轮盖 | ||
| GS0115 | 拆牙连杆凸轮盖螺钉 | ||
| GH397 | 拆牙后曲柄 | ||
| GS039 | 拆牙后曲柄螺钉 | ||
| GL7 | 拆牙曲柄轴位螺母 | ||
| GS640 | 拆牙后曲柄紧固螺钉 | ||
| GS040 | 拆牙轴 | ||
| GR1837 | 拆牙轴油线 | ||
| GO285 | 拆牙轴后挡套 | ||
| GS48 | 拆牙轴后挡套螺钉 | ||
| GR1469 | 拆牙轴后挡套挡圈 | ||
| GS39 | 拆牙轴后挡套挡圈螺钉 | ||
| GO300 | 拆牙轴中挡套 | ||
| GS04 | 拆牙轴中挡套螺钉 | ||
| GO306 | 拆牙轴前挡套 | ||
| GH382 | 拆牙轴前曲柄 | ||
| GS0132 | 拆牙轴前曲柄螺钉 | ||
| GH383 | 牙架连杆 | ||
| GR1841 | 牙架连杆挡圈 | ||
| CS013 | 牙架连杆挡圈螺钉 | ||
| GR1837 | 牙架连杆油线 | ||
| GR1842 | 架连杆锥孔垫圈 | ||
| GS0133 | 架连杆垫圈螺钉 |
Page 33
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | Tension assembly | ||
| 2 | Screw | ||
| 3 | Washer | ||
| 4 | Nut | ||
| 5 | Spring | ||
| 6 | Washer | ||
| 7 | Screw | ||
| 8 | Shaft | ||
| 9 | Screw | ||
| 10 | Lever | ||
| 11 | Screw | ||
| 12 | Nut | ||
| 13 | Lever | ||
| 14 | Screw | ||
| 15 | Shaft | ||
| 16 | Lever | ||
| 17 | Screw | ||
| 18 | Spring | ||
| 19 | Lever | ||
| 20 | Screw | ||
| 21 | Nut | ||
| 22 | Screw | ||
| 23 | Washer | ||
| 24 | Lever | ||
| 25 | Screw | ||
| 26 | Nut | ||
| 27 | Washer | ||
| 28 | Knob | ||
| 29 | Screw | ||
| 30 | Nut | ||
| 31 | Washer | ||
| 32 | Presser bar holder | ||
| 33 | Spring | ||
| 34 | Cap | ||
| 35 | Lever | ||
| 36 | Screw | ||
| 37 | Screw | ||
| 38 | Wire spring | ||
| 39 | Screw | ||
| 40 | Nut | ||
| 41 | Nut |
Page 34
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GS1536/3 | 送料距旋钮部件 | ||
| GS046 | 送料距旋钮螺钉 | ||
| GS047 | 送料调节螺柱 | ||
| GR1538 | 送料调节螺柱O形圈 | ||
| GX345 | 送料距锁合销 | ||
| GW257 | 送料距锁合销簧 | ||
| GR1843 | 送料调节器 | ||
| GX346 | 送料调节器销 | ||
| GS48 | 送料调节器销螺钉 | ||
| GH341 | 送料调节器连杆 | ||
| GS048 | 调节器连杆轴位螺钉 | ||
| GL20 | 调节器连杆轴位螺母 | ||
| GR1540 | 拉簧调节柄柄销 | ||
| GS100 | 拉簧调节柄销螺钉 | ||
| GH342 | 拉簧调节柄 | ||
| GS049 | 调节柄紧固螺钉 | ||
| GS48 | 调节柄定位螺钉 | ||
| GW258 | the | ||
| GR1547 | 拉簧固定板 | ||
| GS01 | 拉簧固定板螺钉 | ||
| GZ282 | 送料料轴 | ||
| GR1542 | 送料料轴O形圈 | ||
| GS1543 | 送料料轴弹性垫圈 | ||
| GR1544 | 送料料数手 | ||
| GS050 | 送料料数手定位螺钉 | ||
| GS033 | 送料料板手螺钉 | ||
| GS051 | 送料料轴端螺钉 | ||
| GR1545 | 送料料轴孔塞 | ||
| GS0134 | 送料料挡块螺杆 | ||
| GR1599 | 挡块螺杆垫圈 | ||
| GL21 | 挡块螺母 | ||
| GR1844 | 送料料挡块 | ||
| GS0135 | 送料料挡块橡胶垫 | ||
| GR1845 | 送料料挡块橡胶垫 | ||
| GH344 | 送料料曲柄定位螺钉 | ||
| GS48 | 送料料曲柄螺钉 | ||
| GS049 | 送料料连杆 | ||
| GH345 | 送料料连杆轴位螺钉 | ||
| GS052 | 送料料连杆轴位垫圈 | ||
| GR1546 | 送料料连杆轴位螺母 | ||
| GL20 | 送料料连杆轴位螺母 |
Page 35
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 52 | Housing | ||
| 53 | Screw | ||
| 36 | Shaft | ||
| 37 | Lever | ||
| 38 | Spring | ||
| 39 | Shaft | ||
| 34 | Pin | ||
| 54 | Shaft | ||
| 51 | Lever | ||
| 33 | Shaft | ||
| 35 | Pin | ||
| 40 | Lever | ||
| 43 | Bush | ||
| 48 | Lever | ||
| 44 | Screw | ||
| 50 | Screw | ||
| 49 | Lever | ||
| 46 | Screw | ||
| 45 | Lever | ||
| 73 | Screw | ||
| 72 | Lever | ||
| 76 | Lever | ||
| 70 | Lever | ||
| 71 | Screw | ||
| 68 | Shaft | ||
| 69 | Shaft | ||
| 65 | Screw | ||
| 67 | Spring | ||
| 66 | Shaft | ||
| 64 | Shaft | ||
| 63 | Screw | ||
| 62 | Pin | ||
| 61 | Shaft | ||
| 59 | Lever | ||
| 60 | Screw | ||
| 10 | Shaft | ||
| 13 | Screw | ||
| 16 | Shaft | ||
| 14 | Bush | ||
| 15 | Screw | ||
| 17 | Screw | ||
| 11 | Shaft | ||
| 12 | Screw | ||
| 20 | Washer | ||
| 21 | Washer | ||
| 19 | Bearing | ||
| 18 | Bearing | ||
| 55 | Pin | ||
| 25 | Shaft | ||
| 22 | Shaft | ||
| 29 | Gear | ||
| 30 | Gear | ||
| 31 | Gear | ||
| 32 | Screw | ||
| 26 | Shaft | ||
| 47 | Lever | ||
| 23 | Shaft | ||
| 27 | Shaft | ||
| 24 | Screw | ||
| 28 | Screw | ||
| 1 | Gear | ||
| 2 | Gear | ||
| 8 | Screw | ||
| 7 | Shaft | ||
| 3 | Shaft | ||
| 4 | Shaft | ||
| 5 | Screw | ||
| 6 | Gear | ||
| 9 | Gear | ||
| 41 | Base | ||
| 42 | Screw | ||
| 58 | Lever | ||
| 57 | Screw | ||
| 56 | Shaft |
Page 36 — 6、弯针勾线分组件 Looper thread retainer components
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GC168 | 上轴伞齿轮 | ||
| GC167 | 弯轴上伞齿轮 | ||
| GO283 | 弯轴上轴套 | ||
| GO280/2 | 弯轴下轴套部件 | ||
| GS04 | 弯轴下轴套螺钉 | ||
| GC167 | 弯轴下伞齿轮 | ||
| GZ307-1 | 竖轴 | ||
| GS033 | 伞齿轮螺钉 | ||
| GC169 | 下轴伞齿轮 | ||
| GZ308 | 下轴 | ||
| GO307 | 下轴后轴套 | ||
| GS04 | 下轴后轴套螺钉 | ||
| GR1847 | 下轴后轴套油毡 | ||
| GO308/2 | 下轴中轴套部件 | ||
| GS04 | 下轴中轴套螺钉 | ||
| GR1848 | 下轴挡圈 | ||
| GS033 | 下轴挡圈螺钉 | ||
| GO311/2 | 下轴挡套部件 | ||
| GS04 | 下轴挡套螺钉 | ||
| GR1849 | 下轴前油封套 | ||
| GR1850 | 下轴前油封 | ||
| GZ309 | 弯针轴 | ||
| GO308/2 | 弯针轴后轴套部件 | ||
| GS04 | 弯针轴后轴套螺钉 | ||
| GO314/2 | 弯针轴前轴套部件 | ||
| GS48 | 弯针轴前轴套螺钉 | ||
| GR1848 | 弯针轴挡圈 | ||
| GS033 | 弯针轴挡圈螺钉 | ||
| GC170 | 主动弯针齿轮 | ||
| GS033 | 主动弯针齿轮螺钉 | ||
| GC171 | 被动弯针齿轮 | ||
| GS033 | 被动弯针齿轮螺钉 | ||
| GH384 | 弯针曲柄 | ||
| GS033 | 弯针曲柄螺钉 | ||
| GS0136 | 弯针曲柄调节螺钉 | ||
| GR1851/5 | 弯针十字接头部件 | ||
| GZ310/3 | 弯针摆轴部件 | ||
| GS0100 | 弯针摆轴盖螺钉 |
Page 37
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | 1 | COLLAR | |
| 2 | 2 | BEVEL GEAR | |
| 3 | 3 | SHAFT | |
| 4 | 4 | COLLAR | |
| 5 | 5 | COLLAR | |
| 6 | 6 | COLLAR | |
| 7 | 7 | SHAFT | |
| 8 | 8 | SCREW | |
| 9 | 9 | GEAR | |
| 10 | 10 | SHAFT | |
| 11 | 11 | SHAFT | |
| 12 | 12 | SCREW | |
| 13 | 13 | SCREW | |
| 14 | 14 | COLLAR | |
| 15 | 15 | SCREW | |
| 16 | 16 | COLLAR | |
| 17 | 17 | SCREW | |
| 18 | 18 | COLLAR | |
| 19 | 19 | COLLAR | |
| 20 | 20 | COLLAR | |
| 21 | 21 | COLLAR | |
| 22 | 22 | SHAFT | |
| 23 | 23 | COLLAR | |
| 24 | 24 | SCREW | |
| 25 | 25 | COLLAR | |
| 26 | 26 | COLLAR | |
| 27 | 27 | COLLAR | |
| 28 | 28 | SCREW | |
| 29 | 29 | GEAR | |
| 30 | 30 | GEAR | |
| 31 | 31 | GEAR | |
| 32 | 32 | GEAR | |
| 33 | 33 | COLLAR | |
| 34 | 34 | COLLAR | |
| 35 | 35 | COLLAR | |
| 36 | 36 | COLLAR | |
| 37 | 37 | SHAFT | |
| 38 | 38 | SHAFT | |
| 39 | 39 | SHAFT | |
| 40 | 40 | COLLAR | |
| 41 | 41 | BASE | |
| 42 | 42 | SCREW | |
| 43 | 43 | COLLAR | |
| 44 | 44 | SCREW | |
| 45 | 45 | SHAFT | |
| 46 | 46 | SCREW | |
| 47 | 47 | LEVER | |
| 48 | 48 | LEVER | |
| 49 | 49 | COLLAR | |
| 50 | 50 | SCREW | |
| 51 | 51 | COLLAR | |
| 52 | 52 | COVER | |
| 53 | 53 | COLLAR | |
| 54 | 54 | COLLAR | |
| 55 | 55 | PIN | |
| 56 | 56 | COLLAR | |
| 57 | 57 | COLLAR | |
| 58 | 58 | COLLAR | |
| 59 | 59 | COLLAR | |
| 60 | 60 | SCREW | |
| 61 | 61 | PIN | |
| 62 | 62 | COLLAR | |
| 63 | 63 | COLLAR | |
| 64 | 64 | SHAFT | |
| 65 | 65 | COLLAR | |
| 66 | 66 | COLLAR | |
| 67 | 67 | COLLAR | |
| 68 | 68 | SHAFT | |
| 69 | 69 | COLLAR | |
| 70 | 70 | SHAFT | |
| 71 | 71 | COLLAR | |
| 72 | 72 | COLLAR | |
| 73 | 73 | COLLAR | |
| 74 | 74 | COLLAR | |
| 75 | 75 | COLLAR | |
| 76 | 76 | COLLAR |
Page 38 — 6、弯针勾线分组件 Looper thread retainer components
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GR1837 | 弯针摆轴油线 | ||
| GR1854 | 弯针摆轴挡圈 | ||
| GR1855 | 弯针架座 | ||
| GS0137 | 弯针架座螺钉 | ||
| GO318 | 弯针摆轴轴套 | ||
| GS032 | 弯针摆轴轴套螺钉 | ||
| GH385 | 左弯针曲柄 | ||
| GS040 | 左弯针曲柄螺钉 | ||
| GN169 | 左弯针 | ||
| GS0138 | 弯针螺钉 | ||
| GH386 | 右弯针曲柄 | ||
| GS040 | 右弯针曲柄螺钉 | ||
| GN170 | 右弯针 | ||
| GK187/7 | 弯针曲柄罩壳部件 | ||
| GS0139 | 曲柄罩壳螺钉 | ||
| GR1462 | 曲柄罩壳孔塞 | ||
| GR1856 | 曲柄罩壳排油管 | ||
| GT162 | 护针凸轮 | ||
| GS48 | 护针凸轮螺钉 | ||
| GH387 | 护针连杆 | ||
| GH388 | 护针叉形曲柄 | ||
| GS019 | 护针叉形曲柄螺钉 | ||
| GX380 | 护针曲柄销 | ||
| GR1837 | 护针曲柄油线 | ||
| GS032 | 护针曲柄销螺钉 | ||
| GO319 | 护针轴套 | ||
| GS48 | 护针轴套螺钉 | ||
| GZ312 | 护针轴 | ||
| GR1837 | 护针轴油线 | ||
| GH389 | 护针曲柄 | ||
| GS040 | 护针曲柄螺钉 | ||
| GR1857 | 摆动护针(1/4") | ||
| GS0100 | 摆动护针杆螺钉 | ||
| GR1858 | 护针杆座 | ||
| GS030 | 护针杆座螺钉 | ||
| GR1859 | 左固定护针杆 | ||
| GR1860 | 右固定护针杆 | ||
| GS011 | 左右固定护针杆螺钉 |
Page 39
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 79 | 79 | ||
| 29 | 29 | ||
| 30 | 30 | ||
| 31 | 31 | ||
| 32 | 32 | ||
| 33 | 33 | ||
| 34 | 34 | ||
| 35 | 35 | ||
| 36 | 36 | ||
| 17 | 17 | ||
| 16 | 16 | ||
| 15 | 15 | ||
| 22 | 22 | ||
| 25 | 25 | ||
| 28 | 28 | ||
| 26 | 26 | ||
| 21 | 21 | ||
| 39 | 39 | ||
| 40 | 40 | ||
| 18 | 18 | ||
| 23 | 23 | ||
| 24 | 24 | ||
| 19 | 19 | ||
| 20 | 20 | ||
| 4 | 4 | ||
| 3 | 3 | ||
| 7 | 7 | ||
| 6 | 6 | ||
| 5 | 5 | ||
| 1 | 1 | ||
| 2 | 2 | ||
| 37 | 37 | ||
| 27 | 27 | ||
| 9 | 9 | ||
| 8 | 8 | ||
| 10 | 10 | ||
| 12 | 12 | ||
| 11 | 11 | ||
| 13 | 13 | ||
| 14 | 14 |
Page 40 — 7、挑线、松线、夹线分组件 Thread take-up, tension, and tension releasing assembly complete
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GH390 | 挑线连杆 | ||
| GS0140 | 挑线连杆螺钉 | ||
| GH392 | 挑线杆 | ||
| GS011 | 挑线杆紧固螺钉 | ||
| GR1861 | 挑线杆夹线板 | ||
| GW294 | 挑线杆夹线簧 | ||
| GS0141 | 挑线杆夹线板轴螺钉 | ||
| GK190 | 挑线杆护罩 | ||
| GS010 | 挑线杆护罩螺钉 | ||
| GR1862 | 线量调节板 | ||
| GS010 | 线量调节板螺钉 | ||
| GR1528 | 调节板螺钉垫圈 | ||
| GR1863 | 中间导线钩 | ||
| GS010 | 中间导线钩螺钉 | ||
| GZ313 | 松线轴 | ||
| GH393/2 | 面线松线曲柄部件 | ||
| GS082 | 面线松线曲柄螺钉 | ||
| GW295 | 抬压脚后杠杆弹簧 | ||
| GR1865 | 后杠杆弹簧固定板 | ||
| GS81 | 后杠杆弹簧固定板螺钉 | ||
| GR1507 | 松线轴挡圈 | ||
| GR1866 | 松线轴油封 | ||
| GR1867 | 松线轴环 | ||
| GR1868 | 夹线器下安装垫 | ||
| GR1869 | 夹线器上安装垫 | ||
| GS0142 | 夹线器上安装垫螺钉 | ||
| GS079 | 夹线器下安装垫螺钉 | ||
| GR1870/19 | 面线夹线器部件 | ||
| GR1871 | 面线单面导线板 | ||
| GR1872 | 面线双面导线板 | ||
| GS0143 | 夹线螺钉 | ||
| GR1488 | 面线夹线板 | ||
| GR1873 | 面线夹线座 | ||
| GW251 | 面线夹线簧 | ||
| GR1490 | 面线止动板 | ||
| GL34/2 | 面线夹线螺母部件 | ||
| GR1875 | 导线钩 | ||
| GS010 | 导线钩螺钉 | ||
| GR1876 | 面线松线爪 | ||
| GS082 | 面线松线爪螺钉 |
Page 41
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 79 | 79 | ||
| 78 | 78 | ||
| 77 | 77 | ||
| 76 | 76 | ||
| 75 | 75 | ||
| 74 | 74 | ||
| 73 | 73 | ||
| 72 | 72 | ||
| 71 | 71 | ||
| 80 | 80 | ||
| 82 | 82 | ||
| 81 | 81 | ||
| 70 | 70 | ||
| 66 | 66 | ||
| 67 | 67 | ||
| 68 | 68 | ||
| 65 | 65 | ||
| 64 | 64 | ||
| 69 | 69 | ||
| 62 | 62 | ||
| 61 | 61 | ||
| 63 | 63 | ||
| 38 | 38 | ||
| 37 | 37 | ||
| 83 | 83 | ||
| 59 | 59 | ||
| 56 | 56 | ||
| 53 | 53 | ||
| 55 | 55 | ||
| 54 | 54 | ||
| 46 | 46 | ||
| 47 | 47 | ||
| 59 | 59 | ||
| 57 | 57 | ||
| 58 | 58 | ||
| 60 | 60 | ||
| 48 | 48 | ||
| 49 | 49 | ||
| 515250 | 515250 | ||
| 45 | 45 | ||
| 43 | 43 | ||
| 41 | 41 | ||
| 42 | 42 |
Page 42 — 7、挑线、松线、夹线分组件 Thread take-up, tension, and tension releasing assembly complete
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GR1877 | 底线打线凸轮 | ||
| GS0144 | 底线打线凸轮定位螺钉 | ||
| GR1878/20 | 凸轮导线钩部件 | ||
| GR1879 | 凸轮导线架 | ||
| GS010 | 凸轮导线架螺钉 | ||
| GR1880 | 底线双线导线钩 | ||
| GR069 | 底线双线导线钩螺钉 | ||
| GW296 | 底线导线止动簧 | ||
| GS069 | 底线导线止动簧螺钉 | ||
| GR1881 | 底线脱线钢丝 | ||
| GS44 | 底线脱线钢丝螺钉 | ||
| GR1882 | 底线脱线钢丝螺钉垫圈 | ||
| GW297 | 底线导线簧 | ||
| GL31 | 凸轮过线螺母 | ||
| GS0145 | 凸轮过线螺钉 | ||
| GR1883 | 凸轮导线钩(右) | ||
| GR1884 | 凸轮脱线爪 | ||
| GR1885 | 凸轮导线钩(左) | ||
| GR1886 | 凸轮导线环 | ||
| GS065 | 凸轮导线钩螺钉 | ||
| GR1887 | 底线导线钩 | ||
| GS0146 | 底线导线钩螺钉 | ||
| GR1888 | 底线导线管 | ||
| GR1889 | 松线轴套 | ||
| GS0123 | 松线轴套螺钉 | ||
| GZ314 | 底线松线轴 | ||
| GR1800 | 底线松线轴O型圈 | ||
| GH395/2 | 底线松线轴曲柄部件 | ||
| GL31 | 底线松线轴螺母 | ||
| GR1891/19 | 底线夹线器部件 | ||
| GR1892 | 夹线器安装板 | ||
| GR1893 | 底线单面导线板 | ||
| GR1894 | 底线双面导线板 | ||
| GX382 | 底线夹线板止转销 | ||
| GS0143 | 夹线螺钉 | ||
| GR1895 | 底线夹线板 | ||
| GW298 | 底线夹线簧 | ||
| GR1896 | 底线夹线止转圈 | ||
| GL36 | 底线夹线螺母 | ||
| GS010 | 夹线器安装板螺钉 | ||
| GR1897 | 底线松线爪 | ||
| GS082 | 底线松线爪螺钉 | ||
| GS2021 | 小线钩 |
Page 43
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | 1 | BASE | |
| 2 | 2 | BRACKET | |
| 3 | 3 | SLEEVE | |
| 4 | 4 | SLEEVE | |
| 5 | 5 | CAP | |
| 6 | 6 | SCREW | |
| 7 | 7 | ROD | |
| 8 | 8 | BRACKET | |
| 9 | 9 | LEVER | |
| 10 | 10 | SPRING | |
| 11 | 11 | SCREW | |
| 12 | 12 | COVER | |
| 13 | 13 | BRACKET | |
| 14 | 14 | BRACKET | |
| 15 | 15 | BRACKET | |
| 16 | 16 | PLATE | |
| 17 | 17 | SPRING | |
| 18 | 18 | BRACKET | |
| 19 | 19 | PIN | |
| 20 | 20 | BRACKET | |
| 21 | 21 | SCREW | |
| 22 | 22 | WIRE | |
| 23 | 23 | WASHER | |
| 24 | 24 | CAP |
Page 44 — 8、润滑分组件 Lubrication
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GR1899/21 | 油泵部件 | ||
| GR1549 | 油泵安装板 | ||
| GR1557 | 上轴供油管接头 | ||
| GR1559 | 下轴供油管接头 | ||
| GR1901 | 油泵垫圈 | ||
| GS0109 | 油泵螺钉 | ||
| GR1902 | 上轴供油管 | ||
| GR1903 | 齿轮供油管橡皮接头 | ||
| GR1904 | 齿轮供油管 | ||
| GR1566 | 齿轮供油管夹 | ||
| GS81 | 齿轮供油管夹螺钉 | ||
| GS3401-7 | 上轴回油管 | ||
| GR1566 | 回油管夹 | ||
| GS81 | 回油管夹螺钉 | ||
| GR1567 | 回油除尘毡 | ||
| GR1568 | 回油毡 | ||
| GR1569 | 回油毡夹 | ||
| GR1906 | 面部挡油板 | ||
| GR1735 | 面部挡油板油线 | ||
| GS069 | 面部挡油板上螺钉 | ||
| GS010 | 面部挡油板下螺钉 | ||
| GR1909 | 下轴供油管 | ||
| GR1562 | 油窗O形圈 | ||
| GR1561 | 油窗 |
Page 45
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 9 | 9 | CAP | |
| 3 | 3 | SPRING | |
| 4 | 4 | COVER | |
| 5 | 5 | COVER | |
| 2 | 2 | COVER | |
| 1 | 1 | COVER | |
| 6 | 6 | WASHER | |
| 7 | 7 | SCREW | |
| 6 | 6 | WASHER | |
| 7 | 7 | SCREW | |
| 10 | 10 | SPRING | |
| 9 | 9 | SPRING | |
| 13 | 13 | LEVER | |
| 11 | 11 | SCREW | |
| 12 | 12 | SPRING | |
| 14 | 14 | SPRING | |
| 15 | 15 | PIN | |
| 16 | 16 | LEVER | |
| 17 | 17 | ROD | |
| 18 | 18 | BRACKET | |
| 19 | 19 | SCREW | |
| 20 | 20 | BRACKET | |
| 21 | 21 | SCREW | |
| 22 | 22 | SPRING | |
| 23 | 23 | SPRING | |
| 24 | 24 | SPRING | |
| 25 | 25 | SPRING | |
| 26 | 26 | SPRING | |
| 27 | 27 | SPRING | |
| 28 | 28 | SPRING |
Page 46 — Oil reservoir & knee lifter components
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | GR1910/13 | Oil reservoir asm. | |
| 2 | GR1911 | Oil reservoir | |
| 3 | GR1576 | Oil reservoir magnet | |
| 4 | GR1912 | Gasket | |
| 5 | GR1913 | Gasket | |
| 6 | GR1575 | Oil drain cap gasket | |
| 7 | GS02 | Oil drain screw | |
| 8 | GR1581 | Knee press lifter rod | |
| 9 | GR1582 | Lifting | |
| 10 | GS056 | Positioning screw | |
| 11 | GS057 | Positioning screw | |
| 12 | GL21 | Nut | |
| 13 | GS058 | Positioning screw | |
| 14 | GL21 | Nut | |
| 15 | GW261 | Spring | |
| 16 | GR1583 | Thrust ring | |
| 17 | GZ283 | Knee press rod | |
| 18 | GR1584 | Bearing bracket | |
| 19 | GS059 | Clamp screw | |
| 20 | GR1586 | Knee lifter plate rod | |
| 21 | GR1587 | Knee predd plate cover joint | |
| 22 | GS08 | Screw | |
| 23 | GR1588 | Knee press plate | |
| 24 | GW262 | Knee press plate spring | |
| 25 | GS060 | Screw | |
| 26 | GKR13 | Knee press plate cover | |
| 27 | GR3408-7 | Small rubber cushion | |
| 28 | GR1578-7 | Big rubber cushion |
Page 47
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | 1 | BRACKET | |
| 2 | 2 | BRACKET | |
| 3 | 3 | BRACKET | |
| 4 | 4 | BLADE | |
| 5 | 5 | SCREW DRIVER | |
| 6 | 6 | SCREW DRIVER | |
| 7 | 7 | SCREW DRIVER | |
| 8 | 8 | NOZZLE | |
| 9 | 9 | OIL BOTTLE | |
| 10 | 10 | TWEEZERS | |
| 11 | 11 | SCREW | |
| 12 | 12 | WASHER | |
| 13 | 13 | SCREW | |
| 14 | 14 | WASHER | |
| 15 | 15 | COVER | |
| 16 | 16 | NUT | |
| 17 | 17 | BRACKET | |
| 18 | 18 | COVER | |
| 19 | 19 | SCREW | |
| 20 | 20 | WASHER |
Page 48 — 10. 机头附件 Machine head accessories
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GR1590/2 | 机头连接部件 | ||
| GR1593 | 机头连接钩座 | ||
| GBX105 | 机头连接座钉 | ||
| GV18 | 机针 | ||
| GR1601 | 螺丝刀(大) | ||
| GR1602 | 螺丝刀(中) | ||
| GR1603 | 螺丝刀(小) | ||
| GBR148 | 机头支柱 | ||
| GR1604/3 | 油箱部件 | ||
| GR558/2 | 镊子 | ||
| GS061 | 罩壳支柱 | ||
| GR1447 | 上轮前罩壳 | ||
| GS062 | 罩壳螺钉 | ||
| GR1599 | 罩壳螺钉垫圈 | ||
| GR1448 | 后罩壳盖 | ||
| GL38 | 后罩壳支柱螺母 | ||
| GS0574 | 前罩壳紧固螺钉 | ||
| GR1449 | 上轮后罩壳 | ||
| GBS120 | 传动带罩壳木螺钉 | ||
| GBR147 | 罩壳木螺钉垫圈 |
Page 49
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | SCREW | ||
| 2 | BRACKET | ||
| 3 | COLLAR | ||
| 4 | COLLAR | ||
| 5 | ARM | ||
| 6 | CLAMP | ||
| 7 | SCREW | ||
| 8 | BRACKET | ||
| 9 | SCREW | ||
| 10 | SCREW | ||
| 11 | SCREW | ||
| 12 | NUT | ||
| 13 | ROD | ||
| 14 | BRACKET | ||
| 15 | ARM | ||
| 16 | BRACKET | ||
| 17 | NUT | ||
| 18 | BRACKET | ||
| 19 | BRACKET | ||
| 20 | SCREW | ||
| 21 | DISC | ||
| 22 | NUT | ||
| 23 | COLLAR | ||
| 24 | WASHER | ||
| 25 | WASHER | ||
| 26 | COLLAR | ||
| 27 | WASHER | ||
| 28 | WASHER | ||
| 29 | NUT | ||
| 30 | WASHER |
Page 50 — 11. 四线团架分组组件 Quadruple-thread spool stand asm.
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GZ315 | 线架杆下节 | ||
| GZ316 | 线架杆上节 | ||
| GR1932 | 线架杆接头 | ||
| GR1744 | 线架杆顶防护橡皮 | ||
| GR1825 | 线架过线杆 | ||
| GR1745 | 线架过线夹 | ||
| GS558 | 线架过线夹螺钉 | ||
| GR1784 | 导线圈 | ||
| GR1933 | 线架导线杆夹 | ||
| GS149 | 线架导线杆夹螺钉(A) | ||
| GS113 | 线架导线杆夹螺钉(B) | ||
| GL104 | 线架导线杆夹螺母 | ||
| GZ317 | 线架导线杆 | ||
| GR1934 | 线架导线杆过线夹 | ||
| GR1935 | 线架导线杆过线 | ||
| GS231 | 线架导线杆过线夹螺钉 | ||
| GL110 | 线架导线杆过线夹螺母 | ||
| GR1825 | 线盘架 | ||
| GR1745 | 线盘架夹 | ||
| GS558 | 线盘架夹螺钉 | ||
| GR1811 | 线盘 | ||
| GL23 | 线盘钉螺母 | ||
| GS067 | 线盘钉 | ||
| GR1625 | 线盘钉弹簧垫圈 | ||
| GR1626 | 线盘钉垫圈 | ||
| GR1215 | 线团防松垫 | ||
| GR1696 | 线架杆紧固螺母垫圈 | ||
| GR1751 | 紧固螺母弹簧垫圈 | ||
| GL158 | 线架杆紧固螺母 | ||
| GR1753 | 线架杆防震橡皮圈 |
Page 51
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 49 | 49 | SCREW | |
| 50 | 50 | WASHER | |
| 51 | 51 | WASHER | |
| 52 | 52 | WASHER | |
| 40 | 40 | COVER | |
| 48 | 48 | COVER | |
| 47 | 47 | COVER | |
| 46 | 46 | COVER | |
| 45 | 45 | MOTOR | |
| 44 | 44 | BRACKET | |
| 43 | 43 | SCREW | |
| 42 | 42 | BRACKET | |
| 41 | 41 | BRACKET | |
| 39 | 39 | BRACKET | |
| 8 | 8 | SCREW | |
| 9 | 9 | WASHER | |
| 10 | 10 | WASHER | |
| 7 | 7 | BRACKET | |
| 1 | 1 | BASE | |
| 2 | 2 | FRAME | |
| 3 | 3 | SCREW | |
| 4 | 4 | WASHER | |
| 5 | 5 | WASHER | |
| 6 | 6 | NUT | |
| 16 | 16 | BRACKET | |
| 15 | 15 | SCREW | |
| 14 | 14 | WASHER | |
| 13 | 13 | NUT | |
| 12 | 12 | BRACKET | |
| 20 | 20 | BRACKET | |
| 22 | 22 | SCREW | |
| 21 | 21 | WASHER | |
| 19 | 19 | BRACKET | |
| 18 | 18 | BRACKET | |
| 26 | 26 | BRACKET | |
| 27 | 27 | SCREW | |
| 28 | 28 | WASHER | |
| 30 | 30 | BRACKET | |
| 23 | 23 | SCREW | |
| 24 | 24 | WASHER | |
| 32 | 32 | BRACKET | |
| 33 | 33 | SCREW | |
| 31 | 31 | BRACKET | |
| 35 | 35 | SCREW | |
| 34 | 34 | BRACKET | |
| 36 | 36 | SCREW | |
| 37 | 37 | WASHER | |
| 38 | 38 | BRACKET |
Page 52 — 12、机架、台板、电器分组件 * Machine stand, table & electric appliance components *
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GKR302/5 | 边架部件(左) | ||
| GKR305/5 | 边架部件(右) | ||
| GKR318 | 边架座套 | ||
| GKL104 | 调节座螺母 | ||
| GKR196/2 | 调节座 | ||
| GKR198 | 调节座胶垫 | ||
| GKR309 | 横档 | ||
| GKS110 | 横档连接螺钉 | ||
| GKR106 | 边架柱弹簧垫圈 | ||
| GKR106 | 边架垫圈 | ||
| GKL101 | 横档固定螺母 | ||
| GKR310 | 踏板轴档 | ||
| GKS110 | 踏板轴档螺钉 | ||
| GKR106 | 踏板轴档弹簧垫圈 | ||
| GKR106 | 踏板轴档垫圈 | ||
| GKR311 | 踏板轴档定位螺母 | ||
| GKX301 | 踏板轴 | ||
| GKR317 | 踏板轴座 | ||
| GKS110 | 踏板轴座螺钉 | ||
| GKR106 | 踏板轴座垫圈 | ||
| GKR106 | 踏板轴座弹簧垫圈 | ||
| GKL101 | 踏板轴座螺母 | ||
| GKR312 | 踏板 | ||
| GKR313 | 踏板垫 | ||
| GKR314 | 踏板衬套 | ||
| GKR315 | 踏板杆 | ||
| GKS102 | 踏板杆螺钉 | ||
| GKR112 | 踏板杆垫圈 | ||
| GKL102 | 踏板杆螺母 | ||
| GKL116 | 下拉杆 | ||
| GKR118 | 上拉杆 | ||
| GKR183 | 拉杆接头 | ||
| GKS110 | 拉杆接头螺钉 | ||
| GKL101 | 拉杆接头螺母 | ||
| GKX101 | 上拉杆开口销 | ||
| GBS114 | 台板木螺钉 | ||
| GKR112 | 台板木螺钉垫圈 | ||
| GKR186 | 台板垫圈 | ||
| GBR156 | 抽斗限位 | ||
| GBR158/2 | 台板组件 | ||
| GBR202/2 | 抽斗部件 | ||
| GBR206 | 抽斗导轨 | ||
| GBS121 | 抽斗导轨木螺钉 | ||
| GD234 | 电机 GFC4024电机 | ||
| GD219 | 电机连接线插头 | ||
| GD108 | 电机接线 | ||
| GD023/3 | 电动带轮 | ||
| GE122 | 机头传动带 | ||
| GKS122 | 电机台板连接螺钉 | ||
| GKR209 | 电机台板连接垫圈 | ||
| GKR106 | 电机台板连接弹簧垫圈 | ||
| GKL101 | 电机台板连接螺母 | ||
| GD227 | 电源开关 | ||
| GBS104 | 电源开关木螺钉 |
Page 53
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 | |||
| 4 | |||
| 5 | |||
| 6 | |||
| 7 | |||
| 8 | |||
| 9 | |||
| 10 | |||
| 11 | |||
| 12 | |||
| 13 | |||
| 14 | |||
| 15 | |||
| 16 |
Page 54 — 13、高速单针链缝机 Model one-needle high speed chainstitcher
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GM274 | 附件安装板 | ||
| GM275/7 | 压脚部件 | ||
| GM276 | 送料牙 | ||
| GM277 | 针 板 | ||
| GR1998 | 弯曲曲柄挡圈 | ||
| GR1999 | 摆动护针杆 | ||
| GR2000 | 固定护针杆 | ||
| GR2001/9 | 面线夹线器部件 | ||
| GR2002 | 面线松线爪 | ||
| GR2003/11 | 底线夹线器部件 | ||
| GR2005 | 底线夹线线爪 | ||
| GR2004 | 夹线器安装板 | ||
| GZ318 | 针 杆 | ||
| GS071 | 支针螺钉 | ||
| GR1481 | 针杆线钩 | ||
| GR1480 | 针杆下衬套线钩 |
Page 55 — List of accessories for double-needle chainstitcher
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GM252 | 1/8"(3.2mm) | ||
| GM255 | 5/32"(4.0mm) | ||
| GM251 | 3/16"(4.8mm) | ||
| GM257 | 7/32"(5.6mm) | ||
| GM248 | 1/4"(6.4mm) | ||
| GM259 | 5/16"(7.9mm) | ||
| GM263 | 3/8"(9.5mm) | ||
| GM266 | 1/2"(12.7mm) | ||
| GM272 |
Page 56 — 双针链缝机 (横列) 附件一览表 List of accessories for double-needle chainstitcher
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GN170 | Right Looper | ||
| GN170 | Right Looper | ||
| GN170 | Right Looper | ||
| GN170 | Right Looper | ||
| GN170 | Right Looper | ||
| GN170 | Right Looper | ||
| GN170 | Right Looper | ||
| GN170 | Left Looper | ||
| GN170 | Left Looper | ||
| GN170 | Bed slide | ||
| GN170 | Cam Cover | ||
| GN170 | Folder | ||
| GN170 | Folder | ||
| GN170 | Folder | ||
| GN170 | Folder | ||
| GN170 | Folder | ||
| GN170 | Folder | ||
| GN170 | Folder | ||
| GN170 | Left Looper | ||
| GN170 | Bed slide | ||
| GN170 | Cam Cover | ||
| GN170 | Folder | ||
| GN170 | Left Looper | ||
| GN170 | Bed slide | ||
| GN170 | Cam Cover | ||
| GN170 | Folder |
Page 57
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | 1 | ||
| 2 | 2 | ||
| 3 | 3 | ||
| 4 | 4 | ||
| 5 | 5 | ||
| 6 | 6 | ||
| 7 | 7 | ||
| 8 | 8 | ||
| 9 | 9 | ||
| 10 | 10 | ||
| 11 | 11 | ||
| 12 | 12 | ||
| 13 | 13 | ||
| 14 | 14 | ||
| 15 | 15 | ||
| 16 | 16 | ||
| 17 | 17 | ||
| 18 | 18 | ||
| 19 | 19 | ||
| 20 | 20 | ||
| 21 | 21 | ||
| 22 | 22 | ||
| 23 | 23 | ||
| 24 | 24 | ||
| 25 | 25 | ||
| 26 | 26 | ||
| 27 | 27 | ||
| 28 | 28 | ||
| 29 | 29 | ||
| 30 | 30 | ||
| 31 | 31 |
Page 58 — 14. 高速三针链缝机 Three needle high speed chainstitch
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GR2113 | 面线夹线器部件 | ||
| GR2112 | 面线松推板 | ||
| GR2120 | 三针夹线器安装板 | ||
| GR2109 | 三针导线勾 | ||
| GR2103 | 三针松勾组件 | ||
| GR2104 | 挑线杆 | ||
| GR2114 | 中间导线勾 | ||
| GR2105 | 底线夹线器部件 | ||
| GR2106 | 底线松推板 | ||
| GR2107 | 三针打线凸轮组件 | ||
| GR2108 | 底线三线导线勾 | ||
| GM282 | 左凸轮导线勾 | ||
| GR2102 | 右凸轮导线勾 | ||
| GR2101 | 底线导线勾 | ||
| GR2100 | 三线凸轮盖 | ||
| GM280 | 针夹 | ||
| GR281 | 机针(14#~18#) | ||
| GN170 | 三针压脚组件 | ||
| GN171 | 保针架 | ||
| GN169 | 压脚板 | ||
| GS788 | 针板 | ||
| GR2119 | 送料牙 | ||
| GR2117 | 右弯针 | ||
| GR2117 | 中弯针 | ||
| GS0140 | 左弯针 | ||
| GR2116 | 三针弯针螺钉 | ||
| GR8744 | 右弯针曲柄 | ||
| GR2117 | 中弯针曲柄 | ||
| GR2117 | 左弯针曲柄 | ||
| GS0140 | 三针弯针曲柄螺钉 | ||
| GR2116 | 摆动护针 | ||
| GR8744 | 左固定护针 |
Page 59
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 24 | 24 | BRACKET | |
| 23 | 23 | SCREW | |
| 25 | 25 | SCREW | |
| 26 | 26 | WASHER | |
| 27 | 27 | SCREW | |
| 28 | 28 | SCREW | |
| 29 | 29 | WASHER | |
| 6 | 6 | PIN | |
| 5 | 5 | BRACKET | |
| 4 | 4 | BRACKET | |
| 1 | 1 | SCREW | |
| 3 | 3 | SCREW | |
| 8 | 8 | BRACKET | |
| 11 | 11 | SCREW | |
| 13 | 13 | SCREW | |
| 12 | 12 | PIN | |
| 14 | 14 | SCREW | |
| 15 | 15 | BRACKET | |
| 16 | 16 | SCREW | |
| 17 | 17 | WASHER | |
| 18 | 18 | SCREW | |
| 19 | 19 | BRACKET | |
| 20 | 20 | SCREW | |
| 21 | 21 | BRACKET | |
| 22 | 22 | SCREW | |
| 30 | 30 | SCREW | |
| 31 | 31 | BRACKET | |
| 32 | 32 | BRACKET | |
| 33 | 33 | SCREW | |
| 34 | 34 | SCREW | |
| 35 | 35 | BRACKET | |
| 36 | 36 | NEEDLE | |
| 37 | 37 | PRESSER FOOT | |
| 38 | 38 | NEEDLE | |
| 39 | 39 | PRESSER FOOT | |
| 40 | 40 | PRESSER FOOT | |
| 41 | 41 | BRACKET | |
| 42 | 42 | SPRING | |
| 43 | 43 | BRACKET |
Page 60 — 15.高速三针厚料链缝机(带拖布轮)分组件(1) Three needle high speed heavy duty (with puller) component
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GS2080 | 拖轮箱螺钉 | ||
| GR8711 | 拖轮箱面板 | ||
| GS044 | 拖轮箱面板螺钉 | ||
| GR8709 | 拖轮箱 | ||
| GR8715 | 拖轮箱支座 | ||
| GR1462 | 拖轮箱孔塞 | ||
| GS2082 | 拖轮箱支座螺钉 | ||
| GR8717 | 提升杠杆 | ||
| GR8714 | 提升滚动轴承 | ||
| GR8719 | 提升滚柱螺钉 | ||
| GR8718 | 提升杠杆螺轴 | ||
| GR8733 | 提升钢丝绳 | ||
| GR8736 | 拉索夹 | ||
| GS2085 | 前拉索夹螺钉 | ||
| GR8735 | 提升钢丝软管 | ||
| GS01 | 拉索夹螺钉 | ||
| GS0142 | 弹簧夹螺钉 | ||
| GS81 | 线夹支座螺钉 | ||
| GR8734 | 提升钢丝调节螺钉 | ||
| GR8725 | 线夹支座 | ||
| GR8737 | 抬压脚后杠杆 | ||
| GL311 | 拉索螺母 | ||
| GS044 | 拖轮箱方盖螺钉 | ||
| GR8710 | 拖轮箱方盖 | ||
| GR8084 | 拖轮箱支板螺栓 | ||
| GS2084 | 拖轮箱支板螺栓垫圈 | ||
| GR8738 | 拖轮箱支板 | ||
| GR3371 | 支板螺钉弹簧垫圈 | ||
| GS2082 | 拖轮箱支板螺钉 | ||
| GS81 | 挡油罩螺钉 | ||
| GR8706 | 挡油罩 | ||
| GR8745 | 挡油罩垫 | ||
| GR8744 | 扳手凸轮组件 | ||
| GS038 | 拖轮板手螺钉 | ||
| GR8746 | 拖轮板手 | ||
| GS044 | 拖轮垫板螺钉 | ||
| GR8730 | 拖轮垫板 | ||
| GM1107 | 针夹 | ||
| GR8743 | 压脚组件 | ||
| GM1106 | 针板 | ||
| GM281 | 送料牙 | ||
| GW1041 | 面线夹线簧 | ||
| GH337 | 抬牙后曲柄 |
Page 61
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| 1 | 1 | Needle Bar | |
| 2 | 2 | Presser Bar | |
| 3 | 3 | Feed Lifting Cam | |
| 4 | 4 | Feed Lifting Link | |
| 5 | 5 | Feed Lifting Connecting Rod | |
| 6 | 6 | Feed Lifting Connecting Rod Screw | |
| 7 | 7 | Presser Bar Connecting Rod | |
| 8 | 8 | Presser Bar Connecting Rod | |
| 9 | 9 | Presser Bar Connecting Rod Screw | |
| 10 | 10 | Presser Bar Connecting Rod | |
| 11 | 11 | Feed Rock Shaft | |
| 12 | 12 | Feed Rock Shaft | |
| 13 | 13 | Feed Rock Shaft | |
| 14 | 14 | Feed Rock Shaft | |
| 15 | 15 | Feed Rock Shaft | |
| 16 | 16 | Feed Wheel | |
| 17 | 17 | Feed Rock Shaft | |
| 18 | 18 | Feed Rock Shaft | |
| 19 | 19 | Feed Rock Shaft | |
| 20 | 20 | Feed Rock Shaft | |
| 21 | 21 | Feed Rock Shaft | |
| 22 | 22 | Feed Rock Shaft | |
| 23 | 23 | Feed Rock Shaft | |
| 24 | 24 | Feed Rock Shaft | |
| 25 | 25 | Feed Rock Shaft | |
| 26 | 26 | Feed Rock Shaft | |
| 27 | 27 | Feed Rock Shaft | |
| 28 | 28 | Feed Rock Shaft | |
| 29 | 29 | Feed Rock Shaft | |
| 30 | 30 | Feed Rock Shaft | |
| 31 | 31 | Feed Rock Shaft | |
| 32 | 32 | Feed Rock Shaft | |
| 33 | 33 | Feed Rock Shaft | |
| 34 | 34 | Feed Rock Shaft | |
| 35 | 35 | Feed Rock Shaft | |
| 36 | 36 | Feed Rock Shaft | |
| 37 | 37 | Feed Rock Shaft | |
| 38 | 38 | Feed Rock Shaft | |
| 39 | 39 | Feed Rock Shaft | |
| 40 | 40 | Feed Rock Shaft | |
| 41 | 41 | Feed Rock Shaft | |
| 42 | 42 | Feed Rock Shaft | |
| 43 | 43 | Feed Rock Shaft | |
| 44 | 44 | Feed Rock Shaft | |
| 45 | 45 | Feed Rock Shaft | |
| 46 | 46 | Feed Rock Shaft |
Page 62 — 16、高速三针厚料链缝机(带拖布轮)分组件(2) Three needle high speed heavy duty (with puller) component(2)
| Ref | Part number | Part name | Qty |
|---|---|---|---|
| GR8712 | 拖轮调压螺母 | ||
| GW1050 | 拖轮压簧 | ||
| GS551-7 | 拖轮压杆滑块螺钉 | ||
| GR8713 | 拖轮压杆滑块 | ||
| GR8714 | 滑块滚动轴承 | ||
| GS2081 | 拖轮箱轴套 | ||
| GO1102 | 拖轮箱轴套 | ||
| GZ951 | 拖轮压杆 | ||
| GS756 | 拖轮架螺钉 | ||
| GR8716 | 拖轮架 | ||
| GR8724 | 拖轮轴卡簧 | ||
| GS970 | 锁紧片螺钉 | ||
| GW650 | 转动锁紧片弹簧 | ||
| GR4382 | 转动锁紧片 | ||
| GR4383 | 转动锁紧滚柱 | ||
| GR8726 | 拖布轮组件 | ||
| GS2083 | 长连杆螺钉 | ||
| GR8721 | 长连杆轴承 | ||
| GH1082 | 长连杆 | ||
| GR8722 | 长连杆垫圈 | ||
| GR8720 | 传动板 | ||
| GL753 | 长连杆杆螺母 | ||
| GR8723 | 拖轮轴 | ||
| GH1081 | 摆动曲柄 | ||
| GL752 | 摆动曲柄螺母 | ||
| GS713 | 摆动曲柄螺钉 | ||
| GR8708 | 摆动曲柄轴套垫圈 | ||
| GO1101 | 摆动曲柄前轴套 | ||
| GZ950 | 摆动曲柄轴 | ||
| GO1101 | 摆动曲柄后轴套 | ||
| GS019 | 驱动摆动曲柄螺钉 | ||
| GL750 | 球连接螺母 | ||
| GH1080 | 驱动摆动曲柄 | ||
| GR8707 | 球连接垫圈 | ||
| GR8705 | 驱动连杆球连接 | ||
| GS0140 | 驱动连杆螺钉 | ||
| GR8704 | 驱动连杆盖 | ||
| GS756 | 驱动连杆 | ||
| GT810 | 驱动连杆组件 | ||
| GR8702 | 驱动偏心轮螺钉 | ||
| GR8703 | 驱动偏心轮 | ||
| GS0115 | 滚动轴承 | ||
| GO1100 | 驱动偏心轮盖板 | ||
| GR2130 | 驱动偏心轮盖板螺钉 |
Siruba L381 — parts catalog
- Page 1 (cover): This is the cover page for the Siruba L381/L382/L383 industrial sewing machine instruction book and parts list. It features the Siruba logo, model numbers, and a picture of the sewing machine.
- Page 2 (text): This page contains important safety instructions for operating and maintaining the sewing machine, including general precautions, specific warnings, and emergency procedures.
- Page 3 (text): This page contains important safety instructions for operating and maintaining the sewing machine, including general precautions, specific warnings, and information about warning symbols.
- Page 4 (text): This page contains safety precautions for operating the sewing machine, including warnings about electrical shock, moving parts, and proper shutdown procedures.
- Page 5 (text): This page contains safety instructions for operating the sewing machine, including warnings about electrical hazards, moving parts, and proper shutdown procedures.
- Page 6 (toc): This page contains the table of contents for the manual, listing sections from "Operation Precautions" to "Parts Manual" with corresponding page numbers.
- Page 7 (toc): This page contains the table of contents for the parts book, listing sections from 'Before operation' to 'PARTS BOOK' with corresponding page numbers.
- Page 8 (text): This page contains important safety precautions and operating instructions for the sewing machine, divided into sections for before operation, pre-start checks, and operating instructions. It also includes a footer with source information.
- Page 9 (text): This page contains specifications for the sewing machine, including stitch type, speed, stitch length, and oiling instructions with diagrams.
- Page 10 (text): This page contains instructions on how to regulate oil amount by manipulating elements on the face plate (Fig. 4) and how to thread the needle thread (Fig. 5). It includes diagrams and step-by-step instructions in both Chinese and English.
- Page 11 (text): This page describes the threading of the bobbin thread for a sewing machine, with instructions in both Chinese and English, accompanied by diagrams labeled Fig. 6 and Fig. 7.
- Page 13 (text): This page contains instructions for adjusting stitch length and setting up the needle, with accompanying diagrams and part information.
- Page 14 (text): This page contains instructions for adjusting the height of the presser bar and the feed dog, with accompanying diagrams and part references.
- Page 15 (text): This page contains instructions for adjusting the needle bar height and the needle and looper, with accompanying diagrams and numbered steps.
- Page 16 (text): This page details the timing adjustment of the looper relative to the needle and the thread-guiding amount of the looper, including diagrams and specific measurements.
- Page 18 (text): This page contains information about the thread adjusting plate, frame thread eyelet, and replacement of the throat plate, with diagrams and corresponding text.
- Page 19 (text): This page contains maintenance instructions for the sewing machine, including daily checks and weekly inspections, followed by a troubleshooting table for common breakdowns.
- Page 20 (text): This page lists common sewing machine problems and their solutions, categorized by issue such as skipped stitches, thread breakage, and needle breakage.
- Page 21 (text): This page contains a troubleshooting guide for sewing machine breakdowns, detailing causes and measures to be taken for thread breakage, skipping stitches, and twisted stitches.
- Page 22 (text): This page lists common problems encountered with sewing machines, such as needle breakage and puckering, along with their potential causes and solutions. It is part of a larger manual, indicated by the page number '15'.
- Page 23 (text): This page contains a footer with page number 16 and a note indicating it is from the library of Superior Sewing Machine & Supply LLC, with a website address jintez.in.
- Page 24 (cover): This is the cover page of a parts book, featuring the title "PARTS BOOK" in English and Chinese characters, along with a watermark and footer information.
- Page 25 (diagram): This page displays a diagram of sewing machine components, including various parts labeled with reference numbers from 1 to 48. The diagram illustrates the main body of the machine, covers, and smaller attached components.
- Page 26 (parts_list): This page lists arm bed components with their part numbers, descriptions, and quantities. It includes parts like the arm bed complete, bed screw stud, bed support, side plate, and various screws and springs.
- Page 27 (diagram): This page displays a diagram of various sewing machine components, including shafts, pulleys, screws, and other mechanical parts, with corresponding reference numbers.
- Page 28 (parts_list): This page lists main shaft and needle bar components, including part numbers, descriptions, and quantities.
- Page 29 (diagram): This page displays a diagram of various sewing machine components, including levers, springs, screws, and other mechanical parts, with reference numbers for identification.
- Page 30 (parts_list): This page lists components for the presser bar, including part numbers, descriptions, and quantities.
- Page 31 (diagram): This page displays a diagram of various sewing machine components, including shafts, levers, and fasteners, with reference numbers for each part.
- Page 32 (parts_list): This page lists feed mechanism components with their reference numbers, part numbers, descriptions, and quantities. It includes parts like feed eccentric cam assemblies, screws, washers, and connecting rods.
- Page 33 (diagram): This page displays a diagram of various sewing machine parts, including a tension assembly, presser bar components, and a spring mechanism, with numbered references for each part.
- Page 34 (parts_list): This page lists parts for the Feed regulating components, including part numbers, descriptions, and quantities.
- Page 35 (diagram): This page displays a diagram of various sewing machine components, including gears, shafts, levers, and fasteners, with corresponding reference numbers.
- Page 36 (parts_list): This page lists looper thread retainer components, including reference numbers, part numbers, descriptions, and quantities.
- Page 37 (diagram): This page displays a diagram of various sewing machine parts, including gears, shafts, levers, and fasteners, with reference numbers for identification.
- Page 38 (parts_list): This page lists looper thread retainer components, including reference numbers, part numbers, descriptions, and quantities.
- Page 39 (diagram): This page contains a diagram illustrating various sewing machine parts, with reference numbers pointing to specific components. The diagram includes parts labeled from 1 to 40 and 79.
- Page 40 (parts_list): This page lists parts for thread take-up, tension, and tension releasing assembly complete, including part numbers, descriptions, and quantities.
- Page 41 (diagram): This page displays a diagram of various sewing machine components, including parts numbered 37 through 83, with detailed illustrations and reference numbers.
- Page 42 (parts_list): This page lists parts for the thread take-up, tension, and tension releasing assembly complete, including part numbers, descriptions, and quantities.
- Page 43 (diagram): This page displays a diagram of sewing machine components, with numbered parts indicated by reference numbers. The diagram includes parts such as screws, caps, and various mechanical elements.
- Page 44 (parts_list): This page lists lubrication components with their part numbers, descriptions, and quantities, including items like oil pump assemblies, rubber joints, screws, and oil tubes.
- Page 45 (diagram): This page displays a diagram of various sewing machine components, including a cover, levers, screws, and other small parts, with reference numbers for identification.
- Page 46 (parts_list): This page lists oil reservoir and knee lifter components, including part numbers, descriptions, and quantities.
- Page 47 (diagram): This page displays a diagram of various sewing machine parts, including screwdrivers, tweezers, a bottle, and mounting brackets, with corresponding reference numbers.
- Page 48 (parts_list): This page lists machine head accessories with part numbers, descriptions, and quantities, including items like machine hinge plates, nails, needles, and various screws and covers.
- Page 49 (diagram): This page displays a diagram of various sewing machine components, including arms, discs, screws, and nuts, with reference numbers for each part.
- Page 50 (parts_list): This page lists parts for the Quadruple-thread spool stand asm., including part numbers, descriptions, and quantities.
- Page 51 (diagram): This page displays a diagram of sewing machine components, with numbered parts and their corresponding references. It includes a list of parts with part numbers and descriptions.
- Page 52 (parts_list): This page lists machine stand, table, and electric appliance components with part numbers, descriptions, and quantities.
- Page 53 (diagram): This page displays a diagram of various sewing machine parts, numbered 1 through 16, with no accompanying part numbers or descriptions.
- Page 54 (parts_list): This page lists parts for Model one-needle high speed chainstitcher, including part numbers, descriptions, and quantities.
- Page 55 (parts_list): This page lists accessories for double-needle chainstitchers, including throat plates, needle clamps, presser feet, feed dogs, and needle guards, with their corresponding part numbers and specifications.
- Page 56 (parts_list): This page is a parts list for accessories for a double-needle chainstitcher, detailing specifications, right looper, left looper, bed slide, cam cover, and folder with corresponding part numbers.
- Page 57 (diagram): This page contains a diagram illustrating various sewing machine parts, with reference numbers pointing to specific components.
- Page 58 (parts_list): This page lists parts for a Three needle high speed chainstitch machine, including part numbers, descriptions, and quantities.
- Page 59 (diagram): This page displays a diagram of various sewing machine parts, including brackets, screws, needles, and presser feet, with reference numbers for each component.
- Page 60 (parts_list): This page lists parts for a Three needle heavy duty sewing machine with a puller component, including part numbers, descriptions, and quantities.
- Page 61 (diagram): This page displays a diagram of sewing machine parts, with numbered components and their corresponding references. It includes parts like a needle bar, presser bar, and various linkages and gears.
- Page 62 (parts_list): This page lists parts for a "Three needle high speed heavy duty (with puller) component(2)" assembly, including reference numbers, part numbers, descriptions, and quantities.
- Page 63 (cover): This is the cover page for the L381/L382/L383 industrial sewing machine instruction book from KAULIN MFG. CO., LTD., dated March 2011.
Page 2
重要安全指示说明 为使您正确使用本机，须对本机的各种功能充分了解，以便安全操作。 使用前请仔细阅读使用说明书。我们希望您能长期愉快地使用本机，请保存好说明书， 以备查阅。 1、无论您何时使用本机，须了解基本的安全事项，包括但不限于下列事项。 2、通读所有说明，并保存好使用说明书。如果需要，请随时翻阅。 3、使用本机前，必须弄清与本机有关安全规定，标准在您的国家是否适用。 4、使用本机前或使用本机时，所有安全装置必须配备齐全。机器运转时，无安全装置属 违章操作，决不允许。 5、操作人员必须经过适当的培训。 6、为了您的人身安全，我们建议您戴上防护眼镜。 7、下列情况下，请关闭电源开关或拔下电源插头。 7.1 机针穿线 7.2 更换机针、压脚、针板、送料牙等 7.3 进行维修时。 7.4 操作区域无人时。 8、在机器加油润滑时，若不小心让油碰到眼睛，皮肤或咽下机油或润滑油，请立即冲洗 被沾染部位或去医院检查。 9、无论机器运转与否，严禁乱动机器零部件和配套装置。 10、机器的维修、改造和调整等工作必须由专业技术人员进行。 11、应由专业受训人员进行一般的维修和检验工作。 12、必须在专业电器人员或专业技术人员的指导下进行有关电器部件的维修，任何电器 部件一经发现受损，立即停止机器运转。 13、使用期间要定期全面彻底清洗机器。 14、正常操作本机时，必须进行试运转，工作环境远离强噪音源，如高频电焊机等。 15、由电器人员选择合适的插头和有地线的插座。 16、若需要改造或改进本机，请采用有效可行的安全措施。本公司对此而产生的伤害 不承担责任。 17、本机只适用于专业缝纫。 18、两种警告提示符 操作人员 特别注意 -i- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 3
IMPORTANT SAFETY INSTRUCTIONS To get the most out of the many functions of this machine and operate it in safety, it is necessary to use this machine correctly. Please read this Instruction Manual carefully before use. We hope you will enjoy the use of your machine for a long time. Please remember to keep this manual in a safe place. 1. Observe the basic safety measures, including, but not limited to the following ones, whenever you use the machine. 2. Read all the instructions, including, but not limited to this Instruction Manual before you use the machine. In addition, keep this Instruction Manual so that you may read it at anytime when necessary. 3. Use the machine after it has been ascertained that it conforms with safety rules/standards valid in your country. 4. All safety devices must be in position when the machine is ready for work or in operation. The operation without the specified safety devices is not allowed. 5. This machine shall be operated by appropriately-trained operators. 6. For your personal protection, we recommend that you wear safety glasses. 7. For the following, turn off the power switch or disconnect the power plug of the machine from the receptacle. 7.1 For threading needle (s) and replacing bobbin. 7.2 For replacing part (s) of needle, presser foot, throat plate, feed dog, cloth guide etc. 7.3 For repair work. 7.4 When leaving the working place of when the working place is unattended. 8. If you should allow oil, grease, etc. used with the machine and devices to come in contact with your eyes or skin or swallow any of such liquid by mistake, immediately wash the contacted areas and consult a medical doctor. 9. Tampering with the live parts and devices, regardless of whether the machine is powered, is prohibited. 10. Repair, remodeling and adjustment works must only be done by appropriately trained technicians or specially skilled personnel. 11. General maintenance and inspection works have to be done by appropriately trained personnel. 12. Repair and maintenance works of electrical components shall be conducted by qualified electric technicians or under the audit and guidance of specially skilled personnel. Whenever you find a failure of any of electrical components, immediately stop the machine. 13. Periodically clean the machine throughout the period of use. 14. Grounding the machine is always necessary for the normal operation of the machine. The machine has to be operated in an environment that is free from strong noise sources such as high-frequency welder. 15. An appropriate power plug has to be attached to the machine by electric technicians. Power plug has to be connected to a grounded receptacle. 16. The machine is only allowed to be used for the purpose intended. Other use are not allowed. 17. Remodel or modify the machine in accordance with the safety rules/standards while taking all the effective safety measures. We assume no responsibility for damage caused by remodeling or modification of the machine. 18. Warning hints are marked with the two shown symbols. Danger of injury to operator or service staff Items requiring special attention -ii- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 4
安全操作事项 1、为避免触电，请不要打开电机的电箱盖，也不要触摸电箱内部组件。 2、为尽可能避免机器运转造成的人身伤害，手指、头部和衣服应远离上轮、皮 带和电机。除此之外，上轮、皮带和电机周围不要放置任何物品。 3、为避免人身伤害，当您打开电源开关或操作机器时，切勿将手放在机针下方。 4、为避免人身伤害，机器运转时，切勿将手伸入挑线罩内。 5、弯针高速运转时，勿将手指放在弯针附近。另外，换弯针时，请关掉机器电 源开关。 6、为尽可能避免人身伤害，当翘起或抬升机头时，勿将手指放入机器内部。 7、为尽可能避免机器的突然启动所造成的事故，抬起机头或移动皮带罩和皮带 时，请关掉机器的电源。 8、如果你的机器配用伺服电机，机器未运转时，电机无噪音。为避免机器的突 然启动所造成的事故，请关掉机器的电源开关。 9、为避免触电，移动电源地线时，请勿让机器运转。 10、为尽可能避免触电或电器组件受损，在插上或拔下插头之前，请关掉电源 开关。 -iii- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 5
FOR SAFE OPERATION 1. To avoid electrical shock hazards, neither open the cover of the electrical box for the motor nor touch the components mounted inside the electrical box. 1. To avoid personal injury, never operate the machine with any of the belt cover, finger guard of safety daevices removed. 2. To prevent possible personal injuries caused by being caught in the machine. keep your fingers, head and clothes away from the handwheel, V belt and the motor while the machine is operation. In addition, place nothing around them. 3. To avoid personal injury, never put your hand under the needle when you turn "ON" the power switch or operate the machine. 4. To avoid personal injury, never put your fingers into the thread take-up cover while the machine is in operation. 5. The looper rotates at a high speed while the machine is in operation, To prevent poss- ible injury to hands, be sure to keep your hands away from the vicinity of the looper during operation.In addition, be sure to turn OFF the power to the machine when replacing the looper. 6. To avoid possible personal injuries, be careful not to allow your fingers in the ma- chine when tilting/raising the machine head. 7. To avoid possible accidents because of abrupt start of the machine, turn OFF the power to the machine when tilting the machine head or removing the belt cover and the V belt. 8. If your machine is equipped with a servo-motor, the motor does not produce noise while the machine is at rest. To avoid possible accidents due to abrupt start of the machine, be sure to turn OFF the power to the machine. 9. To avoid electrical shock hazards, never operate the sewing machine with the ground wire for the power supply removed. 10.To prevent possible accidents because of electric shock or damaged electrial compo- nent(s), turn OFF the power switch in prior to the connection/disconnecti on of the power plug. - iv - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 6 — 目 录
目 录 操作前注意事项 1 一、开车前注意事项 1 二、使用注意事项 1 三、机器规格 2 四、机器的安装 2 五、加油 2 六、面部油量调节 3 七、面线的穿法 3 八、底线的穿法 4 九、夹线器 5 十、压脚 5 十一、针距的调节 6 十二、机针的安装 6 十三、压脚高度的调节 7 十四、送料牙的调节 7 十五、送料牙与针的同步 7 十六、针杆高度的调节 8 十七、机针和弯针的调节 8 十八、弯针相对机针的同步 9 十九、弯针的勾取量 9 二十、弯针和机针间的间隙 9 二十一、保针架的同步 10 二十二、保针架的位置 10 二十三、底线打线凸轮 10 二十四、挑线杆线量调节板的位置 11 二十五、中间导线钩 11 二十六、针板的调换 11 二十七、缝纫机的保养 12 二十八、故障和措施 12 零件手册 17 -V- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 7
Contents Before operation ...{
Page 8
操作前注意事项 / Before operation 注意: 为避免机器受损或发生事故,切记如下: ● 在您初次使用本机前,请彻底清洗,除掉运输过程中的全部灰尘,并充分加油润滑。 ● 确认电压是否正常,插头与电源连接是否正确。 ● 若您的国家的电压与本机电器设计电压不一致,请勿使用本机。 ● 确认电机转动方向是否正确。 ● 使用本机的第一个月,机器应在正常或低于正常转速下运转。 CAUTION: To avoid malfunction and damage of the machine, confirm the following: ● Before you put the machine into operation for the first time after the set-up, clean all dust gathering during transportation and oil it well. ● Confirm that the voltage has been correctly set. Confirm that the power plug has been properly connected to the power supply. ● Never use the machine in the state where the voltage type is inrerent from the designated one. ● Confirm that the direction of rotation of the motor pulley is correct. ● Operate your machine at the normal sewing speed or less for the first month after the set-up. 一、开车前的注意事项 / Pre-start Checks 1、油盘内未加油不能开车。 2、机器运转时,从上轮外侧看转动应为逆时针方向,注意,不能倒转。 3、在最初使用的第一个月中,应把机器转速降低为每分钟4000针进行缝纫作业。 4、按照电动标牌上的标注,检查电源,电压及相数,三相是否正确。 1. The machine shall not be started until the completion of oiling. 2. The rotating direction of the balance wheel, when the machine is started running, shall be in counter-clockwise one. (View from the right side of the balance wheel.) A warning shall be given in advance against making the machine run while balance wheel turning clockwise. 3. The machine shall be under operation at less than 4,000 S.P.M. for the first month. 4. Check power source, voltage, and phase number to see whether they are in accordance with the ratings on the name plate of the motor to be used. 二、使用注意事项 / Operating instructions 1、机器运转时,请勿将手放到针的下部。 2、机器运转时,请勿将手指伸入挑线杆护罩内。 3、机器确定停止后,才能盘动上轮。 4、关掉电机开关后,由于惯性,电动机会继续旋转一段时间,所以要注意,未停止转动不能将 机器倾倒。 5、机器运转时,请勿将手,头发或其它东西靠近或接触上轮、“V”形皮带,电动机,也不要把东西放置在 它们附近。 6、装拆皮带罩及护指器时,请勿开动机器。 1. Do not put your hands under the lower part of the needle when the machine is running. 2. Do not put your fingers into the thread take-up lever cover when the machine is running. 3. Only when the machine stops can you turn the balance wheel by hand. 4. After the motor switch being turned off, due to inertia, the motor will continue to rotate for a while. Be careful not to have the machine tilted unless it stops. 5. Keep away from the balance wheel, V-belt, winder and the motor. 6. Do not start running the machine during mounting or replacing the belt cover, finger guard, etc. -1- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 9
三、机器规格/Specification 线迹形式 并列双针双线链式缝 Stitch type Two-needle double-row chain stitch 速度 最高每分钟4500转 Speed Max.4,500 s.p.m. 针迹长度 1.4~4mm Stitch length 针杆行程 30mm Stroke of needle bar 双线间距 1/8" 5/32" 3/16" 7/32" 1/4" Gauges of double-row 1/8" 5/32" 3/16" 7/32" 1/4" 5/16" 3/8" 1/2" 5/16" 3/8" 1/2" 挑线形式 针杆挑线 Thread take-up type Needle bar thread take up type 弯针 独立调节式样1/8"~1/2"通用 Looper Separately adjustable type, for the range of 1/8" to 1/2" 保针架 摆动式、固定式共用 Needle guard Oscillating type and rigid type 膝提压脚 上升量 8~10mm Light clearance of knee lifter 8~10mm 供油 叶片泵 Oil supply Impeller-type pump 润滑油 2号白油 Lubricating oil #2 white oil 四、机器的安装(图1)/ Installation of the machine (Fig.1) 1. 油盘的安装:将油盘支座①和油盘盒③装在台板枢孔的四 角,用油盘座钉②将其固定,再装上油盘。(图1) 2. 将机头连接钩放入底板孔内,与台板的机头连接钩座相嵌 合,再将机头放到四只脚的缓冲垫上。 1. To install the oil reservoir. Put the oil reservoir rubber cushion ① and oil reservoir felt cushion ③ on four corners of the opening of the table, fix them with the wood screws ②, then install the oil reservoir (Fig1) 2. Put the machine connecting hooks into the holes to engage respe- ctively two hinges seated in the table, then place the machine on the four cushions. 近身侧 Nearbodyside 图1 Fig.1 链侧 Hinge side 五、加油(图2、图3)/ Oiling (Fig.2, Fig.3) 1. 向油盘内加缝纫机油(2号白油)至HIGH记号部位(图2)。 2. 如果油面低于LOW记号,应再加油。 3. 加油后开动机器,润滑正常时,应看到油液喷到油窗上(图3)。 至于喷到油窗上的油量多少与总油量的多少无关,所以不必 担心。 4. 如需换新油,只要拆下油盘的排油螺钉,污油就能排出。 5. 使用新机器或长期未使用的缝纫机时,需抬起压脚以每分 钟3500~4000针的速度空转约10分钟。 1. Oiling shall be made in oil reservoir and the oil surface also be made to level the mark "High" before the machine is started running (Fig.2) 2. Oiling shall be kept on until the oil surface has been brought above the mark "Low" (Fig.3) 3. The normal condition of lubrication is that the oil shall spray onto the oil sight. The amount of oil spraying onto the oil sight is not at all proportional to the total amount of oil in the oil reservoir. There is nothing to worry about. 4. Only when the drain cover screw is loosened and taken off can old oil be drained out and new oil is supplied again. 5. When a new model or those standing idle for long time is to be ope- rated, presser foot shall be lifted and run idle for about ten minutes. 图2 Fig.2 油窗 Oil sight window 图3 Fig.3 -2- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 10 — 六、面部油量调节(图4)/ How to regulate oil amount by means of manipulating elements on the face plate (Fig.4) 七、面线的穿法(图5)/ The threading of needle thread. (Fig.5)
六、面部油量调节(图4)/ How to regulate oil amount by means of manipulating elements on the face plate (Fig.4) 转动油量调节销,可以调节针杆连杆销的供油量调节销的 刻点,靠近针杆连杆销时,油量最小,反之,则油量最大(图4) 注意:调节油量时要十分注意,供油量并不是随调节立刻 变化的。 To turn oil-amount adjusting pin to regulate oil amount of the thread take-up crank,min.oil amount will be supplied when the mark of adjusting pin moves to the thread take-up crank as near as you desire. Otherwise, max.oil amount will be supplied. 图4 Fig.4 刻点 Graduated mark 油量调节销 Oil adjusting pin (最小)油量 Min oil amount (最大) Max.oil amount 七、面线的穿法(图5)/ The threading of needle thread. (Fig.5) 在针杆上升到最高位置时,按图5所示顺序依次穿过各线孔。 1.线从操作者一侧向外穿过机针。 2.面线穿过机针后必须再拉出100mm长线头。 To thread the eyes of the needle as shown in Fig.5: 1) To make thread go through the eye of the needle outwards. (View from the operator's side) 2) To pull out 100mm of the remaining thread after needle thread going through the eyes of the needles. 图5 Fig.5 -3- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 11 — 八、底线的穿法(图6、图7) / The threading of bobbin thread (Fig.6、Fig.7)
八、底线的穿法(图6、图7) / The threading of bobbin thread (Fig.6、Fig.7) 底线按图示顺序依次穿过各线孔。 1、按(图6)所示穿过夹线器单面导线板,如用捻度大的线或缝纫时需送料距大的时候应穿二个孔。 2、把(图7)中的扳簧朝操作人员侧拉,A就向上抬起。 3、穿弯针时,用附件中的镊子按图所示将线穿过,在弯针的前端来出50mm长线头。 To make bobbin thread going through the eye of the needle in the order as shown in (Fig6 and Fig7) 1) Make the bobbin thread go through the tension guide plate; go through the two holes when thread of harder twist fibre is used and feed gauge is wider than usual. 2) Pull the spring toward the operator, as shown in Fig.7 and part A will rise upwads. 3) When threading the looper, the thread shall be made go through the eye of the needle with a tweezer as shown in Fig.7 and 50mm of remaining thread be pulled out. 图7 Fig.7 图6 Fig.6 -4- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 13 — 十一、针距的调节(图13)/To adjust stitch length (Fig.13) 十二、机针的安装(图14、图15)/Setting-up of the needle (Fig.14, Fig.15)
十一、针距的调节(图13)/To adjust stitch length (Fig.13) 1.针迹长度的调节(图13)只要旋转倒料扳手上面的针距调节 旋钮至所需数字即可。旋钮上刻度的数字用mm表示。 2.针迹从大到小改变送料刻度时,一边将倒料扳手朝下 压,一边转动送料旋钮。 3.针迹长度最大是4mm,最小是1.4mm。 4.按下倒料扳手,针迹变为紧密缝(1.4mm),该功能可用于 起始和终止缝或需加强缝的部分。 5.本机不能进行倒缝。 图13 Fig.13 Limit stop Set screw 十二、机针的安装(图14、图15)/Setting-up of the needle (Fig.14, Fig.15) 送料方向 Feed direction 在使用化纤线时,机针针孔的方向不能如(图14)中C的方 向安装。 机针请使TVx7的#9~#21型机针。用化纤线缝制时,可按 (图15)所示形式放置缝油,油箱应另外定制。 When thread of chemical fibre is used, the direction of the needle eye shall not be in that one, as shown in part C of Fig.14. Needle types to be desired fall within the range of #9 to #21 of TVx7; Oil tank shall be custom-made when thread of chemical fibre is used; silicone oil can be placed like that, as indicated in Fig.15. 图14 Fig.14 B A 图15 Fig.15 -6- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 14
十三、压脚高度的调节(图16) / Adjustment of the height of the presser bar: (Fig.16) 为了调换压脚或改变高度、角度需要: 1、拆下面板上的孔塞(图16) 2、旋松压杆导架的紧固螺钉进行调节。 3、调节后旋紧紧固螺钉。 For the requirements of either replacing the presser foot or changing the height and angle of presser foot, the following shall be observed. 1. Take off the rubber plug in the hole from the face plate,as shown in Fig.16. 2. Loosen the presser bar guide bracket set screw. 3. After adjusting, retighten the screw. 十四、送料牙的调节(图17、图18) / Adjustment of the height of the feed dog (Fig.17、Fig.18) 旋松(图18)所示螺钉②,送料牙的 the angle of the A型、B型,送料牙最大突出量是0.8mm,用(图17)中螺钉①调 节。 Loosen the set screw ②, as shown in Fig.18, the angle of the feed dog can be adjusted to the specified one of standard version, A version, and B version. The Max. height of 0.8mm of the proje- ction from dog is adjustable by the adjusting of screw ① as shown in Fig.17 图16 Fig.16 0.8mm 图17 Fig.17 A型 A type B型 B type 图18 Fig.18 十五、送料牙与针的同步(图19) / The timing of feed dog and needle (Fig.19) 针尖下降至针板上平面3mm时, 板上平面以下,此时,正好同步。 送料牙刚好全部下降至针 可调节(图19)中的螺钉。 When the point of needle lowering down to the location of 3mm from the upper surface of the throat plate, the feed dog is right at the position below the upper surface of the throat plate,viz. The running of feed dog being well regulated in relation to the motion of needle. 图19 Fig.19 紧固螺钉 Set screw -7- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 15
十六、针杆高度的调节(图20)/Adjustment of the height of needle bar (Fig.20) 使用TVX7机针时,可用针杆上的刻线,针杆在下死点时, 针杆上刻线对应准针杆下衬套的下端面(如图20所示),这样就 决定了针杆的高度。 When the needle of TVX7 is used, if the graduation on the needle bar is at the bottom dead centre,the mark of graduation shall be in line with the lower end of the needle bar bushing, lower, as indicated in Fig20. 图20 Fig.20 十七、机针和弯针的调节(图21、图22)/Adjustment of the needle and looper (Fig.21, Fig.22) 弯针前后运动量的调节: 按如下顺序调节可得弯针椭圆运动中(图21)所示的B尺寸, 通常B的尺寸在最大时为3.7mm,各种规格的机针都能缝纫。 1.拆下弯针曲柄罩壳上的橡胶塞(图22) 2.用手转动上轮。 3.先旋松定位螺钉和紧固螺钉,调节有标号的螺钉。 4.把调节螺钉上的冲印标记向右旋转,则B的尺寸就会变大, 反之则变小。 5.旋紧定位螺钉和紧固螺钉。 B 针 needle 图21 Fig.21 Adjustment of forward & backward motion of the looper: The dimension of part B of the looper in an elliptic motion can be measured,(refer to Fig21).The max. dimension of part B is usually 3.7mm, suitable for sewing operation of needles of all kinds of sizes. The adjusting procedure is as follows: 1) Take off the rubber plug on the crank case of the looper (refer to Fig22) 2) Turn the balance wheel by hand. 3) First loosen set screw and positioning screw, and then adjust marked screw. 4) Turn clockwise the adjustable screw on which punch mark is printed, and the dimension of part B will be increased in value. 5) Tighten set screw and positioning screw. 调节螺钉 Regulating screw 标记 Mark 图22 Fig.22 -8- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 16
十八、弯针相对机针的同步(图23) / The timing of looper in reference to needle (Fig.23) 机针在最低点时,弯针退到最后,旋松图示齿轮的螺钉进 行同步调整(如图23)。 The looper shall be moved backward to the lowest position while the needle is at the bottom dead centre; loosen the screw on the gear and make timing adjustment of the looper in relation to the needle (refer to Fig 23.) 图23 Fig.23 十九、弯针的勾取量(图24) / Thread-guiding amount of the looper (Fig.24) 1、弯针的针尖到达机针的中心位置时,弯针针尖离机针上端的距离标准值是2mm,此时针杆下端线和针杆 下衬套下端面对齐。(如图24) 2、弯针的后退量约3.5mm。 3、机针孔和弯针孔的相对关系如图24所示。(左右弯针可以分别调整) 1) The standard value of the vertical distance of the point of the looper away from the upper end of the eye of the needle is 2mm, then the graduation mark on the lower part of the needle bar shall be in line with the lower end of the needle bar bushing, lower.(refer to Fig.24) 2) The value of the stroke moved backward by the looper is about 3.5mm. 3) The relation between the eye of the needle and the eye of the looper is indicated Fig.24. (Note that the left looper and the right one can be separately adjusted.) 图24 Fig.24 2mm 3.5mm 二十、弯针和机针间的间隙 / The clearance of looper and needle 保针架调整后,机针和弯针间应留有一定间隙,即用手指轻压机针,机针也不应碰到弯针针尖。如果间隙 太小了,机针的侧面与弯针针尖就会因互相碰撞而损伤。 After adjusting the needle guard, the clearance of a given value between the needle and the looper shall be kept unchanged; the needle shall not touch at the point of the looper when it is pressed down softly. If the clearance is narrower than usual, the side of the needle and the point of the looper are apt to incur breakage due to the impact of the needle side against the looper point. -9- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 18 — The position of the thread-amount adjusting plate of the thread take-up lever (Fig.28) / Frame thread eyelet (Fig.29) / Replacement of throat plate (Fig.30)
二十四、挑线杆线量调节板的位置(图28) / The position of the thread-amount adjusting plate of the thread take-up lever (Fig.28) 针杆在最低点时,如(图28)所示,用挑线杆线量调节板挡 住面线,这样勾取面线时,面线环变大。 此外,针杆在最低处时,也有拉紧面线环的作用,通常 在使用较细的缝纫时,应把线量调节板降到最低点。 The thread-amount adjusting plate will retain the bobbin at bottom dead centre; in such a way to become bigger when the needle the loop of the needle thread is to thread is hooked. In addition to the foregoing there is afunction of the tight pulling of the needle thread loop. The thread-amount adju- sting plate usually reduces to the lowest point when a thread finer than normal is used. Note that take-up thread tension lever is another name for thre- ad-amount adjusting plate. 图28 Fig.28 二十五、中间导线钩(图29) / Frame thread eyelet (Fig.29) 中间导线钩的位置也关系到跳针现象发生,一般把下列位 置作为基准(图29) 棉线#80~#50 中间导线钩刻度2~3 棉线#30~#20 中间导线钩刻度3~4 化纤线#80~#50 中间导线钩刻度1~2 化纤线#30~#20 中间导线钩刻度2~3 图29 Fig.29 The improper-positioning of the frame thread eyelet my be the cause of occurrence of skipping stitch. The following locations are generally regarded as criteria (refer to Fig29) Cotton thread#80~#50 Graduation marked on the frame thread eyelet 2-3 Cotton thread#80~#50 Graduation marked on the frame thread eyelet 3-4 Thread of chemical fibre #80~#50 Graduation marked on the frame thread eyelet 1-2 Thread of chemical fibre #80~#50 Graduation marked on the frame thread eyelet 2-3 二十六、针板的调换(图30) / Replacement of throat plate (Fig.30) 单针链缝机的针板出厂标准规格为1/4" (6.4mm)。(图30) 改变缝线间距通常同时要更换: 1、针夹 2、活压脚 3、针 4、送料牙 5、摆动护针杆 6、卷边器左弯针和右弯针在1/8"~1/2"针板规格之内部通用。 针板宽度大时,除上述零件外还要调换推板和凸轮盖。 The sandard size of the throat plate in parts book, which is 1/4", equivalent to 6.4mm. (Fig.30) stipulated by the manufactory, is The replacement of the following components is ususlly needed at the time when changing the gauge of double-row thread stitch. 图30 Fig.30 Stitch length -11- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 19 — 二十七、缝纫机的保养 / Maintenance of the machine
1.Needle clamp 2.Hinged foot 3.Throat plate 4.Feed dog 5.Rear moving needle guard 6.Curler The left and right loopers within the range of the sizes of 1/8" to 1/2" are inerchangeable. In addition to the aforesaid, replacement of slide plate and cam cover shall be made when the width of thread plate is on the increase. 二十七、缝纫机的保养 / Maintenance of the machine 为了使缝纫机保持良好的工作状态,要做到以下事项: (一)每日必须检查的事项: 1、运转时,油箱内的油有飞溅。 2、运转时,一听到有异常声音,即应停止缝纫作业,并请修理工来检查。 (二)每周一次检查部位: 1、拆下针板、推板、凸轮盖,用刷子清洗送料牙槽中的灰尘。 2、把机头翻转,去除油泵过滤网上的垃圾及油盘内的灰尘。 3、发现润滑油黑时,只需旋下油盘的排油螺钉排空污油,换入新的润滑油。 4、油面必须高于最低线 (LOW) 5、用布揩去沾在油盘磁铁上的黑粉。 The folowing shall be abhered in order to keep the machine in good working condition. (1) Daily checking I. The oil shall spray onto the oil sight when the machine is running. II. Repairman shall be sent for when abnormal sound is heard during the operation of the machine. (2) Locations to be checked once a week: I. To take off throat plate, slide plate,and cam cover; to clean dust of the slotted feed dog with a brush. II. To turn over the head to rid both the oil filter screen on the oil pump and the interior of the oil reservoir of oil stain and dust. III. Loosen drain hole screw and take it off;drain all the dirty oil from the oil reservoir and reoil it. IV.Oil level must be above the lowest oil-level-indicating line marked "Low" V. The black powder,adhering to the magnet in the oil reservoir shall be wiped with sponge cloth. 二十八、故障和措施 /Ommon breakdowns and measures of trouble shooting 序号 事故内容 原 因 对 策 1 断 线 1、缝线质量差 2、缝线太粗 3、机针过热熔断缝线 4、缝线张力太强 5、机针、弯针、针板、保针架过线 部分损伤 6、线量未调节好 1、使用质量好的缝线 2、调换合适的缝线 3、使用硅油或降低转速 4、放松线夹螺母 5、用砂石磨光再抛光 6、调节线量调节板 -12- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 20
2 跳线 1、调整弯针匀取量 2、调整弯针与机针的间隙 3、调整机针同弯针的同步 4、根据线的 情况调整线量 弯针 1、面线跳针 5、调整中间导线钩的位置 6、检查机针安装是否正确 7、检查保针架的位置和同步 是否正确 8、检查缝线是否穿正确 2、底线跳针 1、按上述面线跳针1、2检查 2、检查底线凸轮的同步 3、稍微增强底线的张力 4、检查缝线穿得是否正确 1、使用硅油 3、使用化纤线时的跳针 2、降低转速 3、使用化纤线用的机针 1、降低转速 4、使用合成纤维线时的跳针 2、使用硅油 1、面线张力太弱 1、旋紧底线夹线螺母 3 线迹不良 2、底线张力太弱 2、旋紧底线夹线螺母 3、缝线太粗 3、调换大号机针 4、中间导线钩的位置不够正确 4、调整中间导线钩的位置 5、换线杆线量调节板位置不正确 5、调整线量调节板的位置 6、针眼 6、使用针孔大的针板 4 断针 1、机针弯 1、调换机针 2、送料和机针不同步 2、调整到同步 3、压脚的安装有问题 3、压脚孔、针板孔的中心与 机针中心要一致 4、保针架有问题 4、检查保针架的位置和同步 5、面线张力过强 5、放松面线张力 6、机针太粗 6、使用合适的机针 1、缝线张力过强 1、降低缝线张力,特别是底 线的张力 5 起 约 2、底线凸轮不同步 2、进行调节,使其同步 3、各过线处光洁度有问题 3、研磨各过线部件 4、压脚压力太强 4、旋松压脚螺钉 -13- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 21
No. Breakdown Cause Measures to be taken 1 Therad breakage 1. Poor thread quality 2. Thread being too thick 3. Fusing thread due to high temperature of needle caused by machines operation at high speed 4. Tension being too higher 5. Breakage of needle, looper, throat plate, and needle guard at the location of thread guide 6 Failure to adjust thread amount 1. Quality thread to be used. 2. Replacement to be made by an appropriate thread 3. Silicone oil to be used and speed to be reduced 4. The tension nut to be loosened. 5. First grinding with oil stone and then polishing 6. Adjusting the thread amount adjusting plate 2 Skipping stitch 1.Skipping stitch of needle thread (leaking of two stitches due to the loopers failure to hook the needle thread) 1. Adjusting thread-hooking amount of looper. 2. Adjusting clearance between looper and needle. 3. The timing of needle in reference to looper. 4. Adjusting the thread-amount adjusting plate on thread amount changing conditions. 5. Adjusting the frame thread eyelet. 6. Checking whether the mounting position of the needle is proper or not. 7. To see if the location of needle guard is in an appropriate way and the timing of it is well regulated in relation to another. 8. To see if the needle thread threading is in a proper way. 2. skipping stitch of bobbin thread (leaking of one stitch, needle failure to enter the looper eyelet) 1) Reference to the above cases 1 and 2, as to skipping stitch of the needle of the needle thread. 2) To see if the timing of bobbin thread cam has been well regulated. 3) Increasing tension of bobbin thread a bit higher. 4) To see if the threading of bobbin thread is in a correct way. 3 Twisted stitches 3. Skipping stitch when thread of chemical fribre being in use 4.Skipping stitch when thread of polyester fibre being in use 1. Needle thread tension being too low 2. Bobbin thread tension being too low 3. Sewing thread being too thick 4. Improper position of the frame thread eyelet. 5. Improper position of thread take-up tension plate 6. Throat plate 1) Using sillicone oil 2) Reducing speed 3) Using needle for thread of chemical fibre. 1. Reducing speed 2. Silicone oil to be used 1. Tightening tension nut of needle thread. 2. Tightening tension nut of bobbin thread. 3. Needle of large size to be used. 4. Readjusting it to a proper position. 5. Readjusting its position in an appropriate way. 6. the eyelet of throat plate to be used being bigger than normal one. -14- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 22
1) Needle being bent. 2) The operation of feed dog being not well regulated in reference to the motion of needle. 3) Setting-up of the presser foot. 4) The problem of the timing of the needle guard remaining unsolved 5) Needle thread tension being too high. 6) Needle being too thick. 1) Thread tension being too high. 2) The problem of the timing of the bobbin thread cam for thread guiding failing to be solved. 3) The problem of surface finish arising from bobbin thread going through the parts on the thread guide. 4) The force on the presser foot being too great. 1) Needle to be replaced by another of proper size. 2) Readjusting the timing to feed dog in respect to the needle. 3) To make both the centre of the hole of the presser foot and the centre of the eyelet of the throat. 4) The positioning & the timing of the needle guard to be taken into account. 5) Relaxing needle thread 6) Appropriate needle to be used. 1. Decreasing thread tension; esp. tension of bobbin thread. 2. Readjusting of the very cam said to solve the timing problem. 3. Surface finishing all the parts on the thread guide. 4. Turning counter-clockwise the pressure-regulating screw. 4 Breakage of needle 5 Puckering -15- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 23
- 16- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 24
零件手册 PARTS BOOK - 17 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 25
9 7 8 10 4 5 6 9 40 41 40 41 42 1 43 11 13 12 14 15 40 45 44 38 39 16 3 17 36 37 2 19 26 27 20 48 32 34 33 35 31 30 29 28 21 22 23 24 25 46 47 -18- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 26 — 1、机壳分组件 Arm bed components
1、机壳分组件 Arm bed components 序 号 Ref. No. 件 号 Part No 名 称 Description 数量 Amt. Req. 1 GQ202/13 机壳部件 Arm bed complete 1 2 GS0127 底板支承螺钉 Bed screw stud 2 3 GR1823 底板支承板 Bed support 1 4 GK186 后窗板 Side plate 1 5 GR1812 后窗垫 Gasket 1 6 GS100 后窗板螺钉 Side plate screw 8 7 GR1757/2 面板部件 Face plate asm. 1 8 GR1758 面板垫 Face plate gasket 1 9 GS100 面板螺钉 Screw 3 10 GR1458 面板调节螺孔塞 Rubber plug 2 11 GR1813 凸轮盖压板 Cam cover latch 1 12 GW287 凸轮盖压板弹簧 Spring 1 13 GR1814 凸轮盖压板弹簧座 Spring suspension 1 14 GS069 凸轮盖压板弹簧座螺钉 Screw 1 15 GM241 附件安装板 Attachment installing plate 1 16 GW288 附件安装板弹簧 Spring 1 17 GS0128 附件安装板弹簧螺钉 Screw 2 18 GS012 附件安装板定位螺钉 Screw 1 19 GM242/9 凸轮盖部件 Cam cover asm (1) 20 GM243 凸轮盖 Cam cover 1 21 GW289 凸轮盖托板 Cam cover 1 22 GW290 凸轮盖弹簧 Spring 1 23 GS045 凸轮盖弹簧螺钉 Screw 4 24 GR1815 凸轮盖导轮 Cam cover guide 1 25 GS0129 凸轮盖导轮螺钉 Screw 1 26 GM244/6 推板部件 Bed slide asm. (1) 27 GM245 推板 Bed slide 1 28 GW291 推板弹簧 Spring 1 29 GS045 推板弹簧螺钉 Screw 2 30 GR1816 推板导轮 Bed slide guide 1 31 GS0129 推板导轮螺钉 Screw 1 32 GW292 推板锁簧 Bed slide lock spring 1 33 GS010 推板锁簧螺钉 Screw 2 34 GR1817 推板翼把手 Latch 1 35 GS44 推板翼把手螺钉 Screw 1 36 GR1818 送料轴底板挡油板 Bed oil shield 1 37 GS010 底板挡油板螺钉 Screw 2 38 GR1819 底板挡油板油板 Bed oil shield 1 39 GS010 底板挡油板螺钉 Screw 2 40 GR1461 轴套定位螺孔塞 Rubber plug 4 41 GR1462 上轴套油线孔塞 Rubber plug 2 42 GR1463 针杆柄螺孔塞 Rubber plug 1 43 GR1464 送料针距调节器孔塞 Rubber plug 1 44 GR1465 抬牙轴孔塞 Rubber plug 1 45 GR1466 下轴盲孔塞 Rubber plug 1 46 GR1916/5 卷边部件(1/4") Folder 1 47 GR1923 卷边垫块 Gasket 1 48 GS0148 卷边器螺钉 Screw 2 -19- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 27
13 14 15 16 5 12 11 10 9 8 7 6 4 2 3 1 26 25 24 21 23 17 18 19 20 29 28 27 31 32 30 33 34 35 36 37 39 38 - 20 - Jjintez.in From the library of: Superior Sewing Machine & Supply LLC
Page 28 — 2、上轴针杆分组件 Main shaft & needle bar components
2、上轴针杆分组件 Main shaft & needle bar components 序 号 件 号 Ref. No. Part No 1 GS02 2 GP132 3 GS03 4 GR1468/2 5 GZ303 6 GO262/2 7 GR1824 8 GS33 9 GO265-1 10 GS05 11 GO303/2 12 GS04 13 GR1470 14 GX334 15 GO269 16 GR1471 17 GH378 18 GS06 19 GR1472 20 GS07 21 GH379 22 GS48 23 GS041 24 GH334 25 GO270 26 GS09 27 GO271 28 GS012 29 GR1479 30 GO288 31 GR1478-7 32 GS011 33 GU168-7 34 GZ304 35 GR1826 36 GS0130 37 GV18 38 GR0341-7 39 GS766 名 称 上轴安全螺钉 上轮 上轮螺钉 上轴油封 上轴 上轴后轴套部件 上轴挡圈 上轴挡圈螺钉 上轴中轴套部件 中轴套螺钉 上轴前轴套部件 轴套螺钉 曲柄油量限制毡 曲柄油量调节销 曲柄油量调节销O形圈 针杆曲柄 针杆曲柄定位螺钉 定位螺钉O形圈 针杆曲柄紧固螺钉 针杆连杆销 挑线曲柄定位螺钉 挑线曲柄螺钉 针杆连杆连杆 针杆连杆滚针轴承 针杆连杆左旋螺钉 针杆上衬套 针杆上衬套螺钉 针杆上衬套孔塞 针杆下衬套 针杆连接柱 针杆连接柱螺钉 针杆连接柱滑块 针杆 针夹(1/4") 支针螺钉 机针 针杆接头滑块导轨 滑块导轨螺钉 Description End screw Hand wheel Screw Oil seal Main shaft Main shaft bushing,rear Main shaft thrust collar Screw Main shaft bushing intermediate Screw Main shaft bushing,front Screw Roller felt Crank oil adjusting pin Rubber bushing O-Rubber ring Counterweight asm. Screw O-Rubber ring Screw Needle crank Screw Needle bar crank rod Needle roller bearing Left twist screw Needle bar bushing upper Screw Rubber plug Needle bar bushing, lower Needle bar connection asm Screw Crank slide block Needle bar Needle clamp(1/4") Screw Needle Slide blcok bushing Screw 数 量 Amt. Req. 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 2 - 21 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 29
24 25 28 29 30 31 22 26 29 32 27 33 20 23 35 21 16 15 19 17 18 34 1 2 4 3 6 7 9 5 11 10 8 36 14 13 12 - 22 - From the library of: Superior Sewing Machine & Supply LLC jinttex.in
Page 30
3、压料分组件 Presser bar components 序 号 件 号 Ref. No. Part No 1 GS018 2 GL18 3 GR1494 4 GW253 5 GZ305 6 GR1827 7 GS019 8 GO273 9 GR1525 10 GM246/5 11 GS020 12 GR1832 13 GR1833 14 GS0129 15 GR1499 16 GS021 17 GR1500 18 GR1501/2 19 GR1503 20 GR1504 21 GS022 22 GR1505 23 GS023 24 GS024 25 GR1506 26 GR1508 27 GR1507 28 GR1834 29 GS025 30 GR1510 31 GR1835 32 GS0131 33 GR1836 34 GX378 35 GL19 36 GR1353-7 名 称 调压螺钉 调压螺钉螺母 调压导杆 调压簧 压杆 压杆导架 压杆导架螺钉 压杆衬套 压杆油线 压脚部件1/4" 压脚螺钉 切线刀 切线刀导钩 切线刀导钩螺钉 压脚扳手 压脚扳手螺钉 压脚扳手垫圈 压脚扳手凸轮部件 压脚扳手轴O形圈 压脚升降板 升降板轴位螺钉 抬压脚前杠杆 前杠杆轴位螺钉 前杠杆螺纹销 前杠杆螺纹销垫圈 前杠杆特制开口挡圈 前杠杆开口挡圈 抬压脚拉杆 抬压脚拉杆螺钉 抬压脚拉杆开口挡圈 抬压脚后杠杆 后杠杆轴位螺钉 抬压脚顶杆接头 抬压脚顶杆 抬压脚顶杆螺钉 压杆密封套 Description Presser spring regulator Nut Presser bar guide bar Presser spring Presser bar Presser bar guide bracket asm. Screw Presser bar bushing,lower Oil wick Presser foot asm. Screw Thread knife Thead knife guide Screw Hand lifter Screw Washer Hand lifter cam asm. Rubber ring Lifting lever Hinge screw Lifting link for lifting lever Hing screw Hinge pin Lifting lever gasket Snap ring Snap ring Lifting lever connecting rod Screw Snap ring Lifting lever link rear Hinge screw Swivel Lifting lever connecting rod,vertical Nut Rubber rule 数量 Amt. Req. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 - 23 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 31
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 - 24 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 32 — 4、送料分组件 Feed mechanism components
4、送料分组件 Feed mechanism components 序 号 Ref. No. 件 号 Part No 名 称 Description 数 量 Amt. Req. 1 GT160/10 送料偏心轮部件 Feed eccentric cam asm. 1 2 GT161 送料偏心轮 Feed eccentric cam 1 3 GS034 送料偏心轮螺钉 Screw 2 4 GR1521 送料偏心轮盖板 Feed eccentric thrust washer 1 5 GS035 送料偏心轮盖板螺钉 Screw 1 6 GH335 送料大连杆 Feed rocker shaft connecting rod 3 7 GH380 送料小连杆 Connecting rod 1 8 GX340 送料连杆销 Connecting pin 1 9 GS036 送料连杆销螺钉 Screw 1 10 GR1522 送料摆杆 Feed driving rocker asm. 1 11 GR1523 送料摆杆座 Reed driving rocker 1 12 GX341 送料摆杆座左销 Hinge stud 1 13 GS037 送料摆杆座左销螺钉 Screw 1 14 GX342 送料摆杆座右销 Hinge pin 1 15 GS05 送料摆杆座右销螺钉 Screw 1 16 GZ279 送料摆杆销 Hinge pin 1 17 GS038 送料摆杆销螺钉 Screw 1 18 GS039 送料曲柄轴位螺钉 Hinge screw shaft 1 19 GL7 送料曲柄轴位螺母 Nut 2 20 GH337 送料曲柄 Feed rocker shaft crank 1 21 GS040 送料曲柄螺钉 Screw 1 22 GZ280 送料轴 Feed rocker shaft 1 23 GR1890 送料轴薄挡圈 Thrust collar 1 24 GS032 送料轴薄挡圈螺钉 Screw 2 25 GR1524 送料轴挡圈 Retaining ring 1 26 GO285 送料轴后挡套 Bushing rear 1 27 GS41 送料轴后挡套螺钉 Screw 1 28 GR1469 送料轴挡圈 Thrust collar 1 29 GS39 送料轴挡圈螺钉 Screw 1 30 GZ286 送料轴前挡套 Feed rocker shaft bushing,front 1 31 GR1838 牙架 Feed rocker 1 32 GS0120 牙架螺钉 Screw 1 33 GR1528 牙架座螺钉垫圈 Washer 1 34 GL20 牙架座螺钉垫母 Nut 1 35 GR1839 牙架 Feed bar 1 36 GX396 牙架销 Feed bar shaft 1 37 GS0100 牙架销螺钉 Screw 1 38 GR1837 牙架销油线 Oil wick 1 39 GM247 送料牙1/4" Reed dog (1/4) 2 40 GR1528 送料牙垫圈 Washer 1 41 GS019 送料牙螺钉 Screw 1 42 SM248 送料板1/4" Throat plate(1/4) 1 43 GS044 送料板螺钉 Screw 2 44 GH381 送料牙连杆 Feed driving shaft connecting rod 1 45 GR1840 拆牙连杆凸轮盖 Feed driving eccentric thrust washer 1 46 GS0115 拆牙连杆凸轮盖螺钉 Screw 1 47 GH397 拆牙后曲柄 Feed driving shaft crank rear 2 48 GS039 拆牙后曲柄螺钉 Hinge screw 1 49 GL7 拆牙曲柄轴位螺母 Nut 1 50 GS640 拆牙后曲柄紧固螺钉 Screw 1 51 GS040 拆牙轴 Feed driving shaft 1 52 GR1837 拆牙轴油线 Oil wick 1 53 GO285 拆牙轴后挡套 Bushing,rear 1 54 GS48 拆牙轴后挡套螺钉 Screw 1 55 GR1469 拆牙轴后挡套挡圈 Thrust collar 1 56 GS39 拆牙轴后挡套挡圈螺钉 Screw 2 57 GO300 拆牙轴中挡套 Bushing,intermediate 1 58 GS04 拆牙轴中挡套螺钉 Screw 1 59 GO306 拆牙轴前挡套 Feed rocker shaft bushing,front 1 60 GH382 拆牙轴前曲柄 Feed rocker shaft crank 1 61 GS0132 拆牙轴前曲柄螺钉 Screw 1 62 GH383 牙架连杆 Feed bar link 1 63 GR1841 牙架连杆挡圈 Thrust collar 1 64 CS013 牙架连杆挡圈螺钉 Screw 1 65 GR1837 牙架连杆油线 Oil wick 1 66 GR1842 架连杆锥孔垫圈 Counter-sunk washer 1 67 GS0133 架连杆垫圈螺钉 Screw 2 - 25 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 33
9 8 6 5 1 2 7 4 3 10 11 12 13 17 16 15 41 21 14 28 27 26 25 24 23 22 37 36 35 34 32 29 31 33 30 18 39 40 38 19 20 - 26 - From the library of: Superior Sewing Machine & Supply LLC Jjinte.in
Page 34
5、送料调节组件 Feed regulating components 序 号 件 号 Ref. No. Part No 1 GS1536/3 2 GS046 3 GS047 4 GR1538 5 GX345 6 GW257 7 GR1843 8 GX346 9 GS48 10 GH341 11 GS048 12 GL20 13 GR1540 14 GS100 15 GH342 16 GS049 17 GS48 18 GW258 19 GR1547 20 GS01 21 GZ282 22 GR1542 23 GS1543 24 GR1544 25 GS050 26 GS033 27 GS051 28 GR1545 29 GS0134 30 GR1599 31 GL21 32 GR1844 33 GS0135 34 GR1845 35 GH344 36 GS48 37 GS049 38 GH345 39 GS052 40 GR1546 41 GL20 名 称 Description 送料距旋钮部件 Stitch dial asm. 送料距旋钮螺钉 Screw 送料调节螺柱 Feed regulating screw 送料调节螺柱O形圈 O-Rubber ring 送料距锁合销 Stitch dial lock pin 送料距锁合销簧 Stitch dial lock spring 送料调节器 Feed regulator 送料调节器销 Hinge pin 送料调节器销螺钉 Screw 送料调节器连杆 Feed regulator connecting rod 调节器连杆轴位螺钉 Hingr screw 调节器连杆轴位螺母 Nut 拉簧调节柄柄销 Tension spring suspension stud 拉簧调节柄销螺钉 Screw 拉簧调节柄 Tension spring suspension crank 调节柄紧固螺钉 Clamp screw 调节柄定位螺钉 Screw the Tension spring 拉簧固定板 Suspension bracket 拉簧固定板螺钉 Screw 送料料轴 Reverse feed control lever shaft 送料料轴O形圈 Rubber ring,large 送料料轴弹性垫圈 Waved washer 送料料数手 Reverse feed control lever 送料料数手定位螺钉 Screw 送料料板手螺钉 Screw 送料料轴端螺钉 End screw 送料料轴孔塞 Rubber plug 送料料挡块螺杆 Screw 挡块螺杆垫圈 Washer 挡块螺母 Nut 送料料挡块 Lever stopper 送料料挡块橡胶垫 Rubber cushion 送料料挡块橡胶垫 Control lever crank,rear 送料料曲柄定位螺钉 Screw 送料料曲柄螺钉 Screw 送料料连杆 Feed driving rocker arm connecting 送料料连杆轴位螺钉 Screw 送料料连杆轴位垫圈 Washer 送料料连杆轴位螺母 Nut 数量 Amt. Req. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 -27- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 35
52 53 36 37 38 39 53 34 54 51 33 35 40 43 48 44 50 49 46 43 48 45 44 73 72 76 70 71 68 69 65 67 66 64 63 62 61 59 60 10 13 16 14 15 17 11 12 20 21 19 18 - 28 - From the library of: Superior Sewing Machine & Supply LLC jintex.in 55 25 22 29 30 31 32 26 47 41 42 58 57 56 23 24 28 27 8 1 2 7 3 4 5 5 8 6 9 8
Page 36 — 6、弯针勾线分组件 Looper thread retainer components
6、弯针勾线分组件 Looper thread retainer components 序 号 件 号 名 称 Description 数量 Ref. No. Part No Amt. Req. 1 GC168 上轴伞齿轮 Gear asm. 1 2 GC167 弯轴上伞齿轮 Pinion asm. 1 3 GO283 弯轴上轴套 Bushing,upper 1 4 GO280/2 弯轴下轴套部件 Bushing,lower 1 5 GS04 弯轴下轴套螺钉 Screw 2 6 GC167 弯轴下伞齿轮 Gear asm. 1 7 GZ307-1 竖轴 Upright, shaft 1 8 GS033 伞齿轮螺钉 Bushing, front,asm,screw 8 9 GC169 下轴伞齿轮 Gear asm 1 10 GZ308 下轴 Lower shaft asm. 1 11 GO307 下轴后轴套 Bushing, rear 1 12 GS04 下轴后轴套螺钉 Screw 1 13 GR1847 下轴后轴套油毡 Felt 1 14 GO308/2 下轴中轴套部件 Bushing, intermediate 1 15 GS04 下轴中轴套螺钉 Screw 1 16 GR1848 下轴挡圈 Thrust collar asm 1 17 GS033 下轴挡圈螺钉 Screw 2 18 GO311/2 下轴挡套部件 Bushing,front 1 19 GS04 下轴挡套螺钉 Screw 1 20 GR1849 下轴前油封套 Looper thread guard bushing 1 21 GR1850 下轴前油封 Oil seal 1 22 GZ309 弯针轴 Looper rocker shaft 1 23 GO308/2 弯针轴后轴套部件 Bushing,intermediate 1 24 GS04 弯针轴后轴套螺钉 Screw 1 25 GO314/2 弯针轴前轴套部件 Bushing,front 1 26 GS48 弯针轴前轴套螺钉 Screw 1 27 GR1848 弯针轴挡圈 Thrust collar asm 1 28 GS033 弯针轴挡圈螺钉 Screw 1 29 GC170 主动弯针齿轮 Gear asm.upper 2 30 GS033 主动弯针齿轮螺钉 Screw 1 31 GC171 被动弯针齿轮 Gear asm.lower 2 32 GS033 被动弯针齿轮螺钉 Screw 1 33 GH384 弯针曲柄 Looper crank asm. 2 34 GS033 弯针曲柄螺钉 Screw 1 35 GS0136 弯针曲柄调节螺钉 Looper crank adjusting screw 2 36 GR1851/5 弯针十字接头部件 Trunnion asm. 1 37 GZ310/3 弯针摆轴部件 Looper rocker shaft asm 1 38 GS0100 弯针摆轴盖螺钉 Screw 4 - 29 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 37
30 From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 38 — 6、弯针勾线分组件 Looper thread retainer components
6、弯针勾线分组件 Looper thread retainer components 序 号 件 号 名 称 Description 数量 Ref. No. Part No Amt. Req. 39 GR1837 弯针摆轴油线 Oil wick 1 40 GR1854 弯针摆轴挡圈 Snap ring 2 41 GR1855 弯针架座 Looper mounting base 1 42 GS0137 弯针架座螺钉 Screw 4 43 GO318 弯针摆轴轴套 Bushing,rear 2 44 GS032 弯针摆轴轴套螺钉 Screw 2 45 GH385 左弯针曲柄 Looper holder asm.(left) 1 46 GS040 左弯针曲柄螺钉 Screw 1 47 GN169 左弯针 Looper (left) 1 48 GS0138 弯针螺钉 Screw 1 49 GH386 右弯针曲柄 Looper holder asm. (right) 1 50 GS040 右弯针曲柄螺钉 Screw 1 51 GN170 右弯针 Looper (right) 1 52 GK187/7 弯针曲柄罩壳部件 Crank cover asm 1 53 GS0139 曲柄罩壳螺钉 Screw 3 54 GR1462 曲柄罩壳孔塞 Rubber plug 1 55 GR1856 曲柄罩壳排油管 Vinyl tube 1 56 GT162 护针凸轮 Needle guard crank asm 1 57 GS48 护针凸轮螺钉 Screw 2 58 GH387 护针连杆 Needle guard crank rod 1 59 GH388 护针叉形曲柄 Rear needle guard rocker fork 1 60 GS019 护针叉形曲柄螺钉 Screw 1 61 GX380 护针曲柄销 Pin 1 62 GR1837 护针曲柄油线 Oil wick 1 63 GS032 护针曲柄销螺钉 Screw 1 64 GO319 护针轴套 Bushing 1 65 GS48 护针轴套螺钉 Screw 1 66 GZ312 护针轴 Needle guard driving shaft asm 1 67 GR1837 护针轴油线 Oil wick 1 68 GH389 护针曲柄 Rear needle guard rocker arm asm. 1 69 GS040 护针曲柄螺钉 Screw 1 70 GR1857 摆动护针(1/4") Driving needle guard(1/4) 1 71 GS0100 摆动护针杆螺钉 Screw 1 72 GR1858 护针杆座 Needle guard base 1 73 GS030 护针杆座螺钉 Screw 2 74 GR1859 左固定护针杆 Counter needle guard,left 1 75 GR1860 右固定护针杆 Counter needle guard,right 1 76 GS011 左右固定护针杆螺钉 Screw 2 -31- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 39
79 29 30 31 32 33 34 35 36 17 16 15 22 25 28 26 21 39 40 18 23 24 19 20 4 3 7 6 5 1 2 37 27 9 8 10 12 11 13 14 - 32 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 40 — 7、挑线、松线、夹线分组件 Thread take-up, tension, and tension releasing assembly complete
7、挑线、松线、夹线分组件 Thread take-up, tension, and tension releasing assembly complete 序 号 Ref. No. 件 号 Part No 名 称 Description 数 量 Amt. Req. 1 GH390 挑线连杆 Thread take-up lever 1 2 GS0140 挑线连杆螺钉 Screw 1 3 GH392 挑线杆 Thread take-up 1 4 GS011 挑线杆紧固螺钉 Screw 2 5 GR1861 挑线杆夹线板 Tension plate 1 6 GW294 挑线杆夹线簧 Tension spring 1 7 GS0141 挑线杆夹线板轴螺钉 Screw 1 8 GK190 挑线杆护罩 Thread take-up lever guard 1 9 GS010 挑线杆护罩螺钉 Screw 2 10 GR1862 线量调节板 Take-up thread tension lever 1 11 GS010 线量调节板螺钉 Screw 1 12 GR1528 调节板螺钉垫圈 Washer 1 13 GR1863 中间导线钩 Frame thread eyelet 1 14 GS010 中间导线钩螺钉 Screw 1 15 GZ313 松线轴 Tension release shaft 1 16 GH393/2 面线松线曲柄部件 Tension release arm asm. 1 17 GS082 面线松线曲柄螺钉 Screw 1 18 GW295 抬压脚后杠杆弹簧 Spring 1 19 GR1865 后杠杆弹簧固定板 Suspension bracket 1 20 GS81 后杠杆弹簧固定板螺钉 Screw 2 21 GR1507 松线轴挡圈 Snap ring 1 22 GR1866 松线轴油封 Oil seal ring 1 23 GR1867 松线轴环 Tension release shaft spacer 1 24 GR1868 夹线器下安装垫 Spacer(A) for installing plate 1 25 GR1869 夹线器上安装垫 Spacer(B) for installing plate 1 26 GS0142 夹线器上安装垫螺钉 Screw 1 27 GS079 夹线器下安装垫螺钉 Screw 1 28 GR1870/19 面线夹线器部件 Needle thread tension asm. (1) 29 GR1871 面线单面导线板 Needle thread tension guide plate 2 30 GR1872 面线双面导线板 Tension thread guide 2 31 GS0143 夹线螺钉 Looper thread tension post 2 32 GR1488 面线夹线板 Tension disc 4 33 GR1873 面线夹线座 Tension disc presser tube 2 34 GW251 面线夹线簧 Tension spring 2 35 GR1490 面线止动板 Tension disc stopper 2 36 GL34/2 面线夹线螺母部件 Tension nut 2 37 GR1875 导线钩 Frame thread guide 1 38 GS010 导线钩螺钉 Screw 1 39 GR1876 面线松线爪 Tension release latch 1 40 GS082 面线松线爪螺钉 Screw 1 - 33 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 41
77 76 75 74 73 72 71 79 78 70 66 67 68 65 64 69 62 61 63 59 56 53 55 54 46 47 59 57 58 60 48 49 45 43 41 42 515250 - 34 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 42 — 7、挑线、松线、夹线分组件 Thread take-up, tension, and tension releasing assembly complete
7、挑线、松线、夹线分组件 Thread take-up, tension, and tension releasing assembly complete 序 号 Ref. No. 件 号 Part No 名 称 Description 数 量 Amt. Req. 41 GR1877 底线打线凸轮 Looper thread take-up cam 1 42 GS0144 底线打线凸轮定位螺钉 Screw 1 43 GR1878/20 凸轮导线钩部件 Looper thread guide asm. 1 44 GR1879 凸轮导线架 Thread guide plate 1 45 GS010 凸轮导线架螺钉 Screw 2 46 GR1880 底线双线导线钩 Looper thread guide 1 47 GR069 底线双线导线钩螺钉 Screw 1 48 GW296 底线导线止动簧 Thread guide stopper spring 1 49 GS069 底线导线止动簧螺钉 Screw 2 50 GR1881 底线脱线钢丝 Cast-off wire 1 51 GS44 底线脱线钢丝螺钉 Screw 2 52 GR1882 底线脱线钢丝螺钉垫圈 Washer 2 53 GW297 底线导线簧 Thread guide spring 1 54 GL31 凸轮过线螺母 Nut 1 55 GS0145 凸轮过线螺钉 Thread guide stud 1 56 GR1883 凸轮导线钩(右) Looper thread guide, right 1 57 GR1884 凸轮脱线爪 Cast-off plate 1 58 GR1885 凸轮导线钩(左) Looper thread guide, left 1 59 GR1886 凸轮导线环 Collar 2 60 GS065 凸轮导线钩螺钉 Screw 1 61 GR1887 底线导线钩 Looper thread guide 1 62 GS0146 底线导线钩螺钉 Screw 1 63 GR1888 底线导线管 Looper thread guide tube 1 64 GR1889 松线轴套 Tension release shaft bushing 1 65 GS0123 松线轴套螺钉 Screw 2 66 GZ314 底线松线轴 Looper thread release shaft 1 67 GR1800 底线松线轴O型圈 Rubber ring 1 68 GH395/2 底线松线轴曲柄部件 Tension release arm asm. 1 69 GL31 底线松线轴螺母 Nut 1 70 GR1891/19 底线夹线器部件 Lower thread tension asm. (1) 71 GR1892 夹线器安装板 Tension installing plate 2 72 GR1893 底线单面导线板 Looper thread tension control plate 2 73 GR1894 底线双面导线板 Thread guide 2 74 GX382 底线夹线板止转销 Spring pin 2 75 GS0143 夹线螺钉 Looper thread tension post 2 76 GR1895 底线夹线板 Tension disc 4 77 GW298 底线夹线簧 Looper thread tension spring 2 78 GR1896 底线夹线止转圈 Tension spring bushing 2 79 GL36 底线夹线螺母 Tension post nut 2 80 GS010 夹线器安装板螺钉 Screw 2 81 GR1897 底线松线爪 Looper thread release latch 1 82 GS082 底线松线爪螺钉 Screw 1 83 GS2021 小线钩 Small thread guage 1 -35- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 43
20 18 21 14 17 19 16 15 13 12 11 10 22 9 7 8 10 11 2 1 3 4 5 6 24 23 -36- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 44 — 8、润滑分组件 Lubrication
8、润滑分组件 Lubrication 序 号 件 号 Ref. No. Part No 1 GR1899/21 2 GR1549 3 GR1557 4 GR1559 5 GR1901 6 GS0109 7 GR1902 8 GR1903 9 GR1904 10 GR1566 11 GS81 12 GS3401-7 13 GR1566 14 GS81 15 GR1567 16 GR1568 17 GR1569 18 GR1906 19 GR1735 20 GS069 21 GS010 22 GR1909 23 GR1562 24 GR1561 名 称 Description 油泵部件 Lubricating oil pump asm. 油泵安装板 Oil pump installing base 上轴供油管接头 Rubber joint 下轴供油管接头 Rubber joint 油泵垫圈 Collar 油泵螺钉 Screw 上轴供油管 Main shaft oil tube 齿轮供油管橡皮接头 Oil sight window base 齿轮供油管 Gear oil pipe 齿轮供油管夹 Holder 齿轮供油管夹螺钉 Screw 上轴回油管 Oil return tube asm 回油管夹 Oil return tube holder 回油管夹螺钉 Screw 回油除尘毡 Oil felt presser 回油毡 Oil felt 回油毡夹 Oil felt presser 面部挡油板 Arm oil shield 面部挡油板油线 Oil wick 面部挡油板上螺钉 Screw 面部挡油板下螺钉 Screw 下轴供油管 Oil tube 油窗O形圈 O-Rubber ring 油窗 Oil sight window 数 量 Amt. Req. (1) 1 1 1 3 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 -37- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 45
HIGH LOW -38- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 46 — Oil reservoir & knee lifter components
9、油盘、膝抬压脚分组件 Oil reservoir & knee lifter components 序 号 件 号 Ref. No. Part No 1 GR1910/13 2 GR1911 3 GR1576 4 GR1912 5 GR1913 6 GR1575 7 GS02 8 GR1581 9 GR1582 10 GS056 11 GS057 12 GL21 13 GS058 14 GL21 15 GW261 16 GR1583 17 GZ283 18 GR1584 19 GS059 20 GR1586 21 GR1587 22 GS08 23 GR1588 24 GW262 25 GS060 26 GKR13 27 GR3408-7 28 GR1578-7 名 称 油盘部件 油盘 油盘磁铁 油盘侧面垫 油盘端面垫 排油螺钉O形圈 排油螺钉 抬压脚顶销 抬压脚双向曲柄 双向曲柄螺钉 双向曲柄限位螺钉 双向曲柄限位螺母 双向曲柄调节螺钉 双向曲柄调节螺母 双向曲柄扭簧 抬压脚轴开口挡圈 抬压脚轴 抬压脚操纵杆节头 操纵杆节头螺钉 操纵杆 操纵板节头 操纵板节头螺钉 操纵板 操纵板簧 操纵板螺钉 操纵板软垫 小防震垫 大防震垫 Description Oil reservoir asm. Oil reservoir Oil reservoir magnet Gasket Gasket Oil drain cap gasket Oil drain screw Knee press lifter rod Lifting Positioning screw Positioning screw Nut Positioning screw Nut Spring Thrust ring Knee press rod Bearing bracket Clamp screw Knee lifter plate rod Knee predd plate cover joint Screw Knee press plate Knee press plate spring Screw Knee press plate cover Small rubber cushion Big rubber cushion 数 量 Amt. Req. (1) 1 2 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 -39- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 47
13 14 17 15 12 11 16 18 19 20 10 5 4 8 7 2 3 9 - 40 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 48 — 10. 机头附件 Machine head accessories
10. 机头附件 Machine head accessories 序 号 Ref. No. 件 号 Part No 名 称 Description 数 量 Amt. Req. 1 GR1590/2 机头连接部件 Machine hinge plate asm. 2 2 GR1593 机头连接钩座 Machine hinge plate 2 3 GBX105 机头连接座钉 Nail 4 GV18 机针 Needle 1包 5 GR1601 螺丝刀(大) Screw driver (L) 1 6 GR1602 螺丝刀(中) Screw driver (M) 1 7 GR1603 螺丝刀(小) Screw driver (S) 1 8 GBR148 机头支柱 Machine reat pin 1 9 GR1604/3 油箱部件 Lubricating unit case asm. 1 10 GR558/2 镊子 Tweezer 1 11 GS061 罩壳支柱 Belt cover support stud 1 12 GR1447 上轮前罩壳 Belt-cover A 1 13 GS062 罩壳螺钉 Screw 2 14 GR1599 罩壳螺钉垫圈 Washer 2 15 GR1448 后罩壳盖 Belt-cover B cover asm. 1 16 GL38 后罩壳支柱螺母 Nut 1 17 GS0574 前罩壳紧固螺钉 Screw 1 18 GR1449 上轮后罩壳 Belt-cover B 1 19 GBS120 传动带罩壳木螺钉 Driving belt cover wood screw 2 20 GBR147 罩壳木螺钉垫圈 Wood screw washer 2 -41- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 49
5 4 2 8 3 11 13 12 9 10 15 17 14 16 26 23 21 19 20 1 29 18 25 24 22 30 28 29 27 - 42 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 50 — 11. 四线团架分组组件 Quadruple-thread spool stand asm.
11. 四线团架分组组件 Quadruple-thread spool stand asm. 序 号 件 号 Ref. No. Part No 1 GZ315 2 GZ316 3 GR1932 4 GR1744 5 GR1825 6 GR1745 7 GS558 8 GR1784 9 GR1933 10 GS149 11 GS113 12 GL104 13 GZ317 14 GR1934 15 GR1935 16 GS231 17 GL110 18 GR1825 19 GR1745 20 GS558 21 GR1811 22 GL23 23 GS067 24 GR1625 25 GR1626 26 GR1215 27 GR1696 28 GR1751 29 GL158 30 GR1753 名 称 Description 线架杆下节 Spool reat rod (upper) 线架杆上节 Spool rest rod (lower) 线架杆接头 Spool rested joint 线架杆顶防护橡皮 Spool rest rod rubber cap 线架过线杆 Thread guide asm. 线架过线夹 Thread guide asm joint 线架过线夹螺钉 Screw 导线圈 Thread guide ring 线架导线杆夹 Thread guide arm holder 线架导线杆夹螺钉(A) Screw 线架导线杆夹螺钉(B) Screrw 线架导线杆夹螺母 Nut 线架导线杆 Thread guide arm 线架导线杆过线夹 Thread guide arm holde 线架导线杆过线 Lower thread guide 线架导线杆过线夹螺钉 Screw 线架导线杆过线夹螺母 Nut 线盘架 Spool rest arm. 线盘架夹 Thread guide arm joint 线盘架夹螺钉 Screw 线盘 Spool rest 线盘钉螺母 Nut 线盘钉 Spool pin 线盘钉弹簧垫圈 Spring washer 线盘钉垫圈 Washer 线团防松垫 Spool cushion 线架杆紧固螺母垫圈 Washer 紧固螺母弹簧垫圈 Spring washer 线架杆紧固螺母 Nut 线架杆防震橡皮圈 Rubber washer 数 量 Amt. Req. 1 1 1 1 2* 2* 6** 1 1 1 2 1 1 1 2 2 2* 4*** 4*** 4*** 4*** 4*** 4 2 1 2 2 -43- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 51
49 50 51 52 40 48 47 46 45 44 43 42 41 39 8 9 10 7 1 2 3 4 5 6 16 15 14 13 12 20 22 21 19 18 26 27 28 30 23 24 32 33 31 35 34 36 37 38 - 44 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 52 — 12、机架、台板、电器分组件 * Machine stand, table & electric appliance components *
12、机架、台板、电器分组件 * Machine stand, table & electric appliance components * 序 号 件 号 Description Ref. No. Part No 数量 Amt. Req. 1 GKR302/5 边架部件(左) Stand side asm.left 1 2 GKR305/5 边架部件(右) Stand side asm.right 1 3 GKR318 边架座套 Rubber cushion 4 4 GKL104 调节座螺母 Nut 5 GKR196/2 调节座 Screw 4 6 GKR198 调节座胶垫 Space ring 4 7 GKR309 横档 Stand side support 1 8 GKS110 横档连接螺钉 Screw 4 9 GKR106 边架柱弹簧垫圈 Spring washer 4 10 GKR106 边架垫圈 Washer 8 11 GKL101 横档固定螺母 Nut 4 12 GKR310 踏板轴档 Treadle brace 1 13 GKS110 踏板轴档螺钉 Screw 2 14 GKR106 踏板轴档弹簧垫圈 Spring washer 2 15 GKR106 踏板轴档垫圈 Washer 2 16 GKR311 踏板轴档定位螺母 Treadle brace lock nut 2 17 GKX301 踏板轴 Treadle shaft 1 18 GKR317 踏板轴座 Treadle bracket 2 19 GKS110 踏板轴座螺钉 Screw 2 20 GKR106 踏板轴座垫圈 Washer 4 21 GKR106 踏板轴座弹簧垫圈 Spring washer 2 22 GKL101 踏板轴座螺母 Nut 2 23 GKR312 踏板 Treadle 1 24 GKR313 踏板垫 Gasket 1 25 GKR314 踏板衬套 Collar 2 26 GKR315 踏板杆 Treadle pitman 1 27 GKS102 踏板杆螺钉 Screw 2 28 GKR112 踏板杆垫圈 Washer 4 29 GKL102 踏板杆螺母 Nut 2 30 GKL116 下拉杆 Pitman rod, lower 1 31 GKR118 上拉杆 Pitman rod, upper 1 32 GKR183 拉杆接头 Joint 1 33 GKS110 拉杆接头螺钉 Joint screw 1 34 GKL101 拉杆接头螺母 Joint nut 1 35 GKX101 上拉杆开口销 Pitman rod split pin (upper) 1 36 GBS114 台板木螺钉 Table wood screw 4 37 GKR112 台板木螺钉垫圈 Table wood screw washer 4 38 GKR186 台板垫圈 Table washer 4 39 GBR156 抽斗限位 Drawer limit plate 1 40 GBR158/2 台板组件 Table 1 41 GBR202/2 抽斗部件 Drawer 1 42 GBR206 抽斗导轨 Drawer rail 2 43 GBS121 抽斗导轨木螺钉 Drawer rail wood screw 6 44 GD234 电机 GFC4024电机 Motor GFC4024 motor 1 45 GD219 电机连接线插头 Motor connecting wire plug 1 46 GD108 电机接线 Motor wire 1 47 GD023/3 电动带轮 Motor pulley 1 48 GE122 机头传动带 Machine driving belt 1 49 GKS122 电机台板连接螺钉 Motor & table connecting screw 3 50 GKR209 电机台板连接垫圈 Motor & table connecting washer 3 51 GKR106 电机台板连接弹簧垫圈 Motor & table connecting spring washer 3 52 GKL101 电机台板连接螺母 Motor & table connecting nut 3 53 GD227 电源开关 Power source switch 1 54 GBS104 电源开关木螺钉 Power source switch wood screw 2 * Note that parts above mentioned shall be purchased in a separate order -45- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 53
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 - 46 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 54 — 13、高速单针链缝机 Model one-needle high speed chainstitcher
13、高速单针链缝机 Model one-needle high speed chainstitcher 序 号 件 号 Ref. No. Part No 1 GM274 2 GM275/7 3 GM276 4 GM277 5 GR1998 6 GR1999 7 GR2000 8 GR2001/9 9 GR2002 10 GR2003/11 11 GR2005 12 GR2004 13 GZ318 14 GS071 15 GR1481 16 GR1480 名 称 附件安装板 压脚部件 送料牙 针 板 弯曲曲柄挡圈 摆动护针杆 固定护针杆 面线夹线器部件 面线松线爪 底线夹线器部件 底线夹线线爪 夹线器安装板 针 杆 支针螺钉 针杆线钩 针杆下衬套线钩 Description Attachment installing plate Presser foot asm. Feed dog Throat plate Throat collar Driving needle guard Counter needle guard Needle thread tension asm. Tension release latch Lower thread tension asm. Looper thread release latch Tension installing plate Needle bar Screw Needle bar thread guide Thread guide 数 量 Amt. Req. 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 -47- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 55 — List of accessories for double-needle chainstitcher
双针链缝机(横列)附件一览表 List of accessories for double-needle chainstitcher 规格 Name 针板 Throat plate 针夹 Needle clamp 压脚 Presserfoot asm 送料牙 Feed dog 摆动护针杆 Driving needle guard 右固定护针杆 Counter needle guard right 左固定护针杆 Counter needle guard left Specifications *1 1/8"(3.2mm) GM252 GR1937 GM253/5 GM254 GR1936 2 5/32"(4.0mm) GM255 GR1944 GM256/5 3 3/16"(4.8mm) GM251 GR1929 GM249/5 GM250 4 7/32"(5.6mm) GM257 GR1951 GM258/5 GM247 GR1857 GR1860 GR1859 5 1/4"(6.4mm) GM248 GR1826 GM246/5 6 5/16"(7.9mm) GM259 GR1958 GM260/5 GM261 GR1960 7 3/8"(9.5mm) GM263 GR1966 GM264/5 GM265 8 1/2"(12.7mm) GM266 GR1973 GM267/5 GM268 GR1975 双针纵列链缝机 Vertical Double-needle chainstitcher 9 0 GM272 GR1989 GM271 GM273 GR1992 GR1993 From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 56 — 双针链缝机 (横列) 附件一览表 List of accessories for double-needle chainstitcher
双针链缝机 (横列) 附件一览表 List of accessories for double-needle chainstitcher 名 称 Right Looper 左弯针 Left Looper 推 板 Bed slide 凸轮盖 Cam Cover 卷边器 Folder 规 格 Specifications *1 1/8"(3.2mm) GN170 GM245 GR1939/5 2 5/32"(4.0mm) GR1946/5 3 3/16"(4.8mm) GM243 GR1924/5 4 7/32"(5.6mm) GN169 GR1953/5 5 1/4"(6.4mm) GR1916/5 6 5/16"(7.9mm) GM262 GR1961/5 7 3/8"(9.5mm) GR1968/5 8 1/2"(12.7mm) GM269 GM270 双针纵列链缝机 Vertical Double-needle chainstitcher 9 0 GN170 GN169 GM245 GM243 From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 57
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 - 50 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 58 — 14. 高速三针链缝机 Three needle high speed chainstitch
14. 高速三针链缝机 Three needle high speed chainstitch 序 号 件 号 Ref. No. Part No 1 2 GR2113 3 GR2112 4 GR2120 5 GR2109 6 GR2103 7 GR2104 8 9 GR2114 10 11 GR2105 12 GR2106 13 GR2107 14 GR2108 15 GM282 16 GR2102 17 18 19 GR2101 20 GR2100 21 GM280 22 GR281 23 GN170 24 GN171 25 GN169 26 GS788 27 GR2119 28 GR2117 29 GR2117 30 GS0140 31 GR2116 32 GR8744 名 称 面线夹线器部件 面线松推板 三针夹线器安装板 三针导线勾 三针松勾组件 挑线杆 中间导线勾 底线夹线器部件 底线松推板 三针打线凸轮组件 底线三线导线勾 左凸轮导线勾 右凸轮导线勾 底线导线勾 三线凸轮盖 针夹 机针(14#~18#) 三针压脚组件 保针架 压脚板 针板 送料牙 右弯针 中弯针 左弯针 三针弯针螺钉 右弯针曲柄 中弯针曲柄 左弯针曲柄 三针弯针曲柄螺钉 摆动护针 左固定护针 Description Looper thread asm. Release slide plate Looper thread releage latch Frame thread guide Tension relead latch Thread take-up. Frame thread eyelet Lower thread tension asm. Lower thread release slide plate Looper thread guide asm. Cast-off plate Looper thread guide left Looper thread guide right Thread guide Cam cover Needle clamp Needle Presser foot asm. Finger guard Presser foot Throat plante Feed dog Right looper Middle looper Left looper Screw Looper holder asm.(right) Looper holder asm.(middle) Looper holder asm.(left) Screw Driving needle guard Counter needle guard 数 量 Amt. Req. 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 6 1 1 1 3 1 1 - 51 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 59
24 23 25 26 27 28 29 6 5 4 1 3 8 11 13 12 14 15 16 17 18 19 20 21 22 30 31 32 33 34 35 36 37 38 39 40 41 42 43 - 52 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 60 — 15.高速三针厚料链缝机(带拖布轮)分组件(1) Three needle high speed heavy duty (with puller) component
15.高速三针厚料链缝机(带拖布轮)分组件(1) Three needle high speed heavy duty (with puller) component 序 号 件 号 名 称 Description 数 量 Amt. Req. Ref. No. Part No 1 GS2080 拖轮箱螺钉 Screw 3 2 GR8711 拖轮箱面板 Puller plate 1 3 GS044 拖轮箱面板螺钉 Screw 3 4 GR8709 拖轮箱 Puller box 1 5 GR8715 拖轮箱支座 Puller box support 1 6 GR1462 拖轮箱孔塞 Rubber cap 1 7 GS2082 拖轮箱支座螺钉 Screw 2 8 GR8717 提升杠杆 Lever 1 9 GR8714 提升滚动轴承 Ball bearing redial 1 10 GR8719 提升滚柱螺钉 Screw 1 11 GR8718 提升杠杆螺轴 Shoulder screw 1 12 GR8733 提升钢丝绳 Wire 1 13 GR8736 拉索夹 Wire holder 1 14 GS2085 前拉索夹螺钉 Screw 2 15 GR8735 提升钢丝软管 Soft tube 1 16 GS01 拉索夹螺钉 Screw 1 17 GS0142 弹簧夹螺钉 Screw 1 18 GS81 线夹支座螺钉 Screw 2 19 GR8734 提升钢丝调节螺钉 Screw 1 20 GR8725 线夹支座 Thread tension suppe 1 21 GR8737 抬压脚后杠杆 Lifting lever link rear 1 22 GL311 拉索螺母 Nut 2 23 GS044 拖轮箱方盖螺钉 Screw 2 24 GR8710 拖轮箱方盖 Puller cover 1 25 GR8084 拖轮箱支板螺栓 Bolt 1 26 GS2084 拖轮箱支板螺栓垫圈 Washer 1 27 GR8738 拖轮箱支板 Puller support plate 1 28 GR3371 支板螺钉弹簧垫圈 Washer spring 1 29 GS2082 拖轮箱支板螺钉 Screw 1 30 GS81 挡油罩螺钉 Screw 2 31 GR8706 挡油罩 Oil-protection cover 1 32 GR8745 挡油罩垫 Oil-protection gaskets 1 33 GR8744 扳手凸轮组件 Lifter shaft asm. 1 34 GS038 拖轮板手螺钉 Screw 1 35 GR8746 拖轮板手 Lifter 1 36 GS044 拖轮垫板螺钉 Screw 1 37 GR8730 拖轮垫板 Puller base plate 1 38 GM1107 针夹 Needle clamp 1 39 GR8743 压脚组件 Presser foot asm. 1 40 GM1106 针板 Throat plate 1 41 GM281 送料牙 Feed dog 1 42 GW1041 面线夹线簧 Tension spring 3 43 GH337 抬牙后曲柄 Feed driving shaft crank rear 1 -53- From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 61
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 - 54 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 62 — 16、高速三针厚料链缝机(带拖布轮)分组件(2) Three needle high speed heavy duty (with puller) component(2)
16、高速三针厚料链缝机(带拖布轮)分组件(2) Three needle high speed heavy duty (with puller) component(2) 序 号 件 号 Ref. No. Part No 1 GR8712 2 GW1050 3 GS551-7 4 GR8713 5 GR8714 6 GS2081 7 GO1102 8 GZ951 9 GS756 10 GR8716 11 GR8724 12 GS970 13 GW650 14 GR4382 15 GR4383 16 GR8726 17 GS2083 18 GR8721 19 GH1082 20 GR8722 21 GR8720 22 GL753 23 GR8723 24 GH1081 25 GL752 26 GS713 27 GR8708 28 GO1101 29 GZ950 30 GO1101 31 GS019 32 GL750 33 GH1080 34 GR8707 35 GR8705 36 GS0140 37 38 39 GR8704 40 GS756 41 GT810 42 GR8702 43 GR8703 44 GS0115 45 GO1100 46 GR2130 名 称 拖轮调压螺母 拖轮压簧 拖轮压杆滑块螺钉 拖轮压杆滑块 滑块滚动轴承 拖轮箱轴套 拖轮箱轴套 拖轮压杆 拖轮架螺钉 拖轮架 拖轮轴卡簧 锁紧片螺钉 转动锁紧片弹簧 转动锁紧片 转动锁紧滚柱 拖布轮组件 长连杆螺钉 长连杆轴承 长连杆 长连杆垫圈 传动板 长连杆杆螺母 拖轮轴 摆动曲柄 摆动曲柄螺母 摆动曲柄螺钉 摆动曲柄轴套垫圈 摆动曲柄前轴套 摆动曲柄轴 摆动曲柄后轴套 驱动摆动曲柄螺钉 球连接螺母 驱动摆动曲柄 球连接垫圈 驱动连杆球连接 驱动连杆螺钉 驱动连杆盖 驱动连杆 驱动连杆组件 驱动偏心轮螺钉 驱动偏心轮 滚动轴承 驱动偏心轮盖板 驱动偏心轮盖板螺钉 上轴前轴套部件 针杆曲柄 Description Presser spring regulateor Presser spring Screw Presser bar guide bracket Ball bearing radial Screw Shaft tube(lower) Presser bar Screw Puller bracket Open ring Screw Sring Wheel Rolling axis Puller asm. Screw Ball bearing radial Connecting rod Washer Wheel connecting rod Nut Puller shaft Adjusting rod(left) Nut Screw Washer Shaft tube(left) Shaft Shaft tube(right) Screw Nut Ad justing rod(right) Washer Ball scwer Screw Connecting rod cover Connecting rod Connecting rod asm. Screw Eccentric wheel Needle driving lever bearing Eccentric wheel thrust washer Screw Main shaft bushing front Counter weingt asm. 数 量 Amt. Req. 1 1 1 1 1 1 1 1 1 1 6 6 2 6 1 2 2 1 2 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 - 55 - From the library of: Superior Sewing Machine & Supply LLC jintex.in
Page 63 — L381/L382/L383
K R L381/L382/L383 高林股份有限公司 KAULIN MFG. CO., LTD. jintex.in The specification and/or appearances of the equipment described in this instruction book are subject to change because of modification without previous notice. jintex.in MAR. 2011